1 | Overhead line grips pressed loops
Overhead line grips with 1 pressed loop. Galvanized Bowden wire. Highest tensile strength over entire length and tension resulting from variable mesh 3-2-1-strand. Produced and colour-coordinated according to DIN EN 48207-2. These grips with pressed loops are for conventional pulling operations but not for negotiating capstans or tensioner heads, for this select hand spliced grips below, types MSP. All Vetter grips are handmade therefore of high flexibility. They adapt easy at any difference in conductor diameter and are therefore simple to handle.
  • L1 = the lengths without cables in. L2 = total length included the loops.
  • The real length mounted on the cable can be much shorter, depending on the cable diameter.
  • These grips are produced according to DIN EN 48207-2
  • B = internal diameter of the loop
  • D = thickness of the loop
  • kN = minimum breaking load
,Overhead-line-grips-swivels,Overhead-line-swivels-electric-conductive,Tire-câble-chaussettes-lignes-aérienne,Emerillons-lignes-aériennes,Emerillons-lignes-aériennes-conductible,Mallas-lineas-aéreas,Empalmes-rigidos-conexión,Empalmes-giratorios-de-lineas-aérias
,,,
,,,
,,,
,,,
,,,
CodeTypeD Sect. mm² B D kN L1/L2 mm Colour kg
540070 MS 116-11 25-50 30 8 18 840/1050 violet 0,20
540120 MS 1611-16 50-120 40 10 36 960/1210 green 0,40
540170 MS 2116-21 120-210 60 10 66 1300/1600 yellow 0,70
540220 MS 2721-27 210-340 70 12 93 1640/2000 grey 1,40
540260 MS 3827-38 380-680 70 14 135 1740/2140 red 1,80
540310 MS 4538-45 680 -....... 70 14 150 1930/2330 brown 2,10
2 | Overhead line grips spliced loops
Overhead line grips with 1 hand-spliced loop. Galvanized Bowden wire. Highest tensile strength over entire length and tension resulting from variable mesh 3-2-1-strand. Produced and colour-coordinated according to DIN EN 48207-2. These grips with hand-spliced loops are suitable for negotiating capstans or tensioner heads. All Vetter grips are handmade therefore of high flexibility. They adapt easy at any difference in conductor diameter and are therefore simple to handle.
  • L1 = the lengths without cables in. L2 = total length included the loops.
  • The real length mounted on the cable can be much shorter, depending on the cable diameter.
  • These grips are produced according to DIN EN 48207-2
  • B = internal diameter of the loop
  • D = thickness of the loop
  • kN = minimum breaking load
,,,
,,,
,,,
,,,
,,,
,,,
,,,
CodeTypeD mm² B D kN L1/L2 mm Colour kg
540410 MSP 116-11 25-50 35 8 18 840/1290 violet 0,28
540420 MSP 1611-16 50-120 45 11 36 960/1500 green 0,55
540430 MSP 2116-21 120-210 50 16 66 1300/2000 yellow 0,90
540440 MSP 2721-27 210-340 55 18 93 1640/2470 grey 2,10
540450 MSP 3827-38 380-680 60 20 135 1740/2620 red 2,80
540460 MSP 4538-45 680 -....... 72 20 150 1930/2860 brown 3,20
540470 MSP 5545-55 680 -....... 72 22 150 2500/3540 blue 4,20
3 | Line connecting grips
Rope connecting grips. Suitable for changing crane ropes. Not to use for overhead lines, for this it is recommended to use 2 MS grips and 1 FVD swivel. Connecting grips would be destroyed by the torsion between two conductors. kN = Minimum Breaking Load

,,,
,,,
,,,
,,,
,,,
,,,
CodeTypeD kN Length kg
540560 SVS 106-10 6,6 1000 0,10
540600 SVS 1510-15 10,2 1500 0,13
540650 SVS 2015-20 20,4 1500 0,27
540660 SVS 2520-25 22,2 2000 0,40
540700 SVS 3025-30 24,3 2000 0,49
540750 SVS 4030-40 35,1 2000 0,60
4 | Line connection
For connecting two lines the most reliable method is to use two overhead line grips MS or MSP 11-45, as above shown. These will be connected by a swivel type FVD to avoid torsion.
  • One set for safe working consist of the followings:
  • Code 540.xxx - two overhead line grips as shown above
  • Code 537.xxx - one overhead line swivel with ball bearings to avoid torsion.
,,,
,,,
CodeTypeArticle Overhead line grips
540500 MS-MSPArticle see 0,00
540500 MS-MSPArticle see 0,00
5 | Connector rigid
Rigid line connecter for overhead line pulling, for connection of different pull ropes, slim construction for easy running through the pulleys. These swivels are suitable for pulling over capstans or line tensioner.

kN = Minimum Breaking Load
,,,
,,,
,,,
,,,
,,,
CodeTypeD L Fork Bolt kN kg
537010 FTS 2828 59 11 17 69 0,14
537040 FTS 4141 74 14 19 111 0,35
537080 FTS 4848 91 19 20 159 0,53
537120 FTS 5656 102 19 22 219 0,77
537170 FTS 6060 121 26 27 360 1,05
6 | Overhead line swivels
Overhead line swivels, colour silver, connection between pulling rope and pulling grip. With ball bearings, therefore only suitable to absolute twist-free steel ropes. Avoids untwisting the conductor. These swivels may not be used for pulling over capstans or line tensioner. For this please use above mentioned types FTS 28-60. Swivels with high electrical conductivity for working in the neighbourhood of live wires you can find in the sectors below.

kN = Minimum Breaking Load in straight pull.
,,,
,,,
,,,
,,,
,,,
,,,
,,,
,,,
,,,
,,,
,,,
,,,
CodeTypeD L Fork Bolt kN kg
537280 FVD 1818 80 6,5 6 21 0,11
537300 FVD 2525 109 9 10 45 0,30
537360 FVD 3030 128 12 12 60 0,50
537410 FVD 3535 137 12 14 90 0,70
537490 FVD 4040 160 14 16 120 1,10
537550 FVD 5055 187 18 16 165 1,90
537580 FVD 5555 190 20 18 180 2,30
537640 FVD 6060 220 23 20 225 3,10
537670 FVD 6565 235 26 24 300 3,50
537700 FVD 7575 270 30 27 320 6,70
537730 FVD 8585 305 35 30 400 9,40
537760 FVD 100100 340 38 36 500 14,30
7 | Conductor pulling equipment electrical conductive
Overhead line pull connectors, for pulling conductors in the neighbourhood of live wires instead of using pulling grips. To complete the safety use only swivels with high electrical conductivity, e.g. FED tested up to 84 Ampere. Please ask for more information.
 
For a complete conductor pulling set the following below listed single parts are necessary:
  • 1 Swivel electrical conductive
  • 1 Cardan joint to connect the line pull connector with the swivel
  • 1 Line pull connector according to the conductor diameter
  • 1 Solid cone according to the conductor diameter
,,,
CodeTypeNeeded parts
538000 LZK-KombiSee description above 0,00
8 | Swivels electrical conductive
Overhead line swivels. With high electrical conductivity to deflect induced currents in the neighbourhood of live wires. With ball bearings, therefore only suitable to absolute twist-free steel ropes. Avoids untwisting the conductor. These swivels may not be used for pulling over capstans or line tensioner. For this please use above mentioned types FTS 28-60.

Amp. = Deflecting induced currents. kN = minimum breaking load.
,,,
,,,
,,,
CodeTypeD Amp. L Fork Bolt kN kg
537820 FED 4040 84 160 14 16 150 1,22
537835 FED 5555 170 190 20 18 180 2,65
537840 FED 6565 170 235 26 24 300 3,75
9 | Cardan joints
Cardan joints for connection of the pull connector with the swivels FED electrical conductive.
  • Together with the swivels it functions like a globe joint.
  • Important also when pulling in level differences
  • kN = Minimum Breaking Load
,,,
,,,
,,,
,,,
,,,
CodeTypeFor connector Swivel kN kg
538855 LKG 40-40OD 40 FED 40 150 2,16
538860 LKG 45-45OD 45 FED 45 150 2,36
538865 LKG 50-50OD 50 FED 50 165 2,85
538870 LKG 55-55OD 55 FED 55 180 3,30
538875 LKG 60-60OD 60 FED 60 180 4,10
10 | Line pull connectors
Overhead line pull connectors, for pulling conductors in the neighbourhood of live wires instead of using pulling grips. To complete the safety use only swivels with high electrical conductivity, e.g. FED from 84 to 170 Ampere. Please ask for more information.
  • Overhead line grips are tending to burst open at a spark erosion.
  • The conductor stringing clamps together with the swivels FED are continuously conductive.
  • A safe connection to avoid destruction and the fall down of the conductors.
  • The pulling clamp can be reused often.
  • kN = Minimum Breaking Load
,,,
,,,
,,,
,,,
,,,
,,,
CodeTypeD Cond.-D mm² kN kg
538802 LZK 40-07040 9,6-12,0 50-70 60 1,16
538805 LZK 40-12540 13,6-16,3 95-125 60 1,16
538810 LZK 45-18545 17,1-19,0 150-185 75 1,60
538812 LZK 50-26550 20,3-22,4 210-265 90 2,22
538814 LZK 55-38555 24,1-26,7 300-385 120 2,30
538818 LZK 60-57060 27,5-32,5 385-570 125 2,90
11 | Solid cone taper key for connectors
Solid cone taper key for connectors
  • Exact conductor diameter is needed for an offer
,,,
,,,
,,,
,,,
,,,
,,,
,,,
,,,
CodeTypeCond-D For connector kg
538822 KEL 9,69,6-10,5 LZK 40-070 0,05
538824 KEL 11,711,7-13,6 LZK 40-070 0,05
538826 KEL 15,515,5-16,3 LZK 40-125 0,06
538828 KEL 17,117,1-19,0 LZK 45-185 0,06
538830 KEL 20,320,3-22,4 LZK 50-265 0,09
538832 KEL 24,124,1-25,0 LZK 55-385 0,13
538834 KEL 26,726,7-27,0 LZK 55-385 0,15
538836 KEL 28,828,8-29,5 LZK 60-570 0,18
12 | Mounting tool
Mounting tool for overhead line pull connectors. Made of special high quality steel. For beating in round taper keys.

,,,
CodeTypeZu Cross section Cond.-D Dimension kg
538880 LKT 40-6040-570 mm² 9-32 30/12x160 0,40