The calibration sets MKV 0810 and MKV 1116 in conjunction with the accessory micro- transmitter SKS 06 (code-no. 231941) and SKS 07 (code-no. 231954) are destined for the calibration of subducts with an internal diameter 8,0 to 16,0 mm. The calibration can be done for single subducts as well as for multi subducts. By the calibration defects or blockages on the subducts can be detected in advance thus a good blowing-in performance can be achieved. The MKV 0810 set contains two calibres with different diameters for the calibration of subducts with internal diameter 8,0 or 9,8-10,0 mm. The MKV 1116 set contains three different calibres for testing subducts of ID 11,4-16,0 mm. The calibres are easily screwed onto the micro-transmitter and blown through the subducts by air-pressure. The set also contains all essential connectors, reducing nipples as well as a catcher for the micro-transmitter. The catcher has to be used in order to avoid damages to the micro-transmitter. The air-pressure for the calibration has to be limited to max. 4 bars for MKV 0810 and to max. 2 bars for MKV 1116. By applying a higher pressure the micro-transmitter might be damaged by hitting duct blockages or by hard crashing into the catcher at the very end. The set contains the following parts:

The calibration set MKK 0606 in conjunction with the micro transmitter SKS 04 is foreseen to calibrate subducts with inner diameter D 6.0 mm only. The calibration can be performed for single subducts as well as for multi subducts in buried and protective pipe installed versions. This new calibration set supports the blowing-in of mini- and micro cables on a completely new level since the quality of a sub duct installation can be checked in general.

The set comprises of 3 calibres with protection sponge having a diameter of 4.8 mm, a collecting device for the pipe end, a spare battery cover and 2 spare batteries. The calibre will be simply unscrewed on the micro transmitter and with the sponge ahead blown-into the pipes using compressed air. The micro transmitter is a precision engineered measuring device, which has to be handled in the civil engineering with special care. Never operate the transmitter without protection sponge, bumper and collecting device fixed at the end of the pipe. Attentions should be paid to max. possible bending radius and air injection pressure ??" too high air pressure can cause damages on the calibration set.

During backward blowing the enclosed collecting device has to be used or at least a sufficient padding of another collecting device shall be implemented.

Multi ducts can be detected in short distances through the average duct of dia. 12x2,0 or 14x2,0 mm laying in the centre. The micro transmitter SKS 06 of diam. 6,4 mm and SKS 07 of diam. 7,5 mm are screwed on the M5 thread of the mini-rod diam. 3 mm. The obtainable pushing length depends on the local condition but is limited anyway by the max. length of the mini rod of 50 m. Using lubricant relieves pushing and pulling back the transmitter. Detection depth in the ground is max. 2 m. The yellow or red mini rod can be used for inserting the micro transmitter.

The catching device guarantees that the micro-transmitter is safely caught at the end of the tube and does not hit the ground unprotected.

The micro transmitter enters the catching device and is caught in the circular guide until it comes to a stop. This prevents the micro transmitter from being damaged or destroyed.

Locating device with 2 batteries, for locating blown-in calibres in cable protection pipes or in subducts (micro pipes), as well as for locating non-metallic pipelines and blockages with the pipe coils, yellow or red D 4.5-11. There are the following possible applications:

FigarinO. The FOC basket is used if the cable is to long to be blown completely with only one blowing machine. When half of the cable is installed in one direction the remaining cable is pushed into the FigarinO with the blowing machine. Out of the FigarinO this part of the cable can be blown uncut in the opposite direction to finish the installation. A second application is "overblowing" longer cables. Instead of laying these on figure of eight on the floor they can be blown in the FigarinO. After opening the FigarinO the cable ring can be turned around and the cable can be blown-in totally.

Cable bow for pushing-in the cable into the FigarinO with the Minijet

Sponge for sub duct cleaning and pre-lubricating prior to cable blowing

Cable guiding heads for screwing on the cable heads for friction-low sliding during cable-blowing.

Cable crash test tube transparent with sealing end. For limiting the pushing force of the blowing-in machines. Tests without compressed air. For determination of the cable stiffness up to the crash. Safe packed in reusable plastic duct.

Essential for fail-safe adjustment of the pushing force of all different cable blowing machines. Duct-length 1 m.

Sub duct connector with two couplings. For closing an intermediate blowing position of a duct-OD 10 mm, on a length of max. 400 mm. Set of 3 pcs.

Air connector for subduct calibration sets.

Included in MicroJet PRM 196 and in Minijet P 02.

Air connectors for subduct calibration sets and for high pressure test units.

Conduit plug for fixing on duct-OD with hose safety coupling applicable for duct calibration, duct pressure tests, duct cleaning etc.

Conduit sealing plug applicable for duct pressure tests.

Air regulator with manometer for subduct calibration set.

Included in MicroJet PRM 196

Air regulator with manometer for subduct calibration set.

With safety couplings for air pressure hoses.

DPV 1 pressure test distribution unit from 0-10 bar with 2 ball valves, with measuring connection 1215 for DRG 10 and DPG 17U for high pressure testing of tube OD 7-110 mm, for KR tube or 1 subduct (micro tube)

Consisting of:

Case for micro cabling accessory, with 9 shelves as following:

Cable blow-in stop for in-house and underground fibre cable installations for cable lengths up to 200 m. Transparent duct with sponge shock absorber.

The standard rope winch is equipped with hand operated rope guide and a rope protection cover according to the rules. The winch can be equipped with the mechanical rope length measuring device SLM 510. For pulling-in fibre optic cables, subducts or delicate cables with the electronic digital line pull data recorder with USB interface, see below. For safety reason the pulling force on the bottom of drum is limited to 5,0 kN.

Cable side cutter for micro and mini FOC cables up to dia. 4,0 mm, length 125 mm. Knife special hardened also for Aramid and Kevlar.

Cable cutter for Cu-/Al and FOC cables up to D 20 mm / 70 mm². Precision ground, hardened blades, therefore clean and smooth cut. Insulated with multi-component grips, VDE-tested. Length 200 mm.

Conduit slitter for lengthwise and circumferential slitting of plastic conduits and cable covers. Complete reinforced steel version. In case 195x75x45 mm.

This cable conduit saw SRS 6.1 is a further development of the proven SRS 6. The saw is suitable for cutting occupied and unoccupied cable conduits without damaging internal cables or subducts. The saw is suitable for conduits at an outer diameter of 32-150 mm and at a max. wall thickness up to 6 mm. The saw can precisely cut lengthwise and crosswise and can also precisely cut windows into the cable conduit. Especially for long cuts on the cable conduits which are necessary for cable line redirections the great benefits of this saw pay off.

The cutting depth can be precisely adjusted to a 1/10 of a millimetre by an adjustment mechanism thus the cables inside the cable conduit are well-protected. The cutting depth has always to be set 0,2 mm less than the conduits wall thickness. The remaining very thin plastic membrane will be removed by a lifter tool thus the cable is also protected during this final step. The conduit guiding plates allow a high safety at work as well as accurate cuts. The guiding plates are available for the below mentioned conduit-diameters. The cordless saw is handy and small in order to be fit for application also in narrow working conditions its weight is below 2 kg. Included in delivery are the following parts:

Sub duct slitter for lengthwise slitting. Supplied with a protecting cap.

Sub duct slitter for lengthwise slitting and circumferential slitting of plastic conduits and cable covers. Cutter for empty and occupied subducts and dismantler for multiducts. Special thin and grinded turning guide shoe blade. Special shape of handle reduces danger of injury. Incl. 2 spare turning blades, e.g. 4 single blades.

Subduct cutter for occupied or empty subducts.

Subduct cutter for occupied or empty subducts.

Subduct cutting tongs, only for use with empty subducts.

Subduct cutting tongs, only for use with empty subducts.

If the cross-section of a microtube is altered, the DuctDoc helps to return the microtube to its original shape with a round cross-section. Applicable for ID: 3.5 / 4 / 5.5 / 6 / 8 / 10 / 11.4 / 12 / 13 / 15 / 16 mm

Burring tool for in- and outside of plastic conduits. Of lightweight aluminium