ULTIMAZ E25, blow fibre units and micro cable blowing device especially for in-house cabling up to lengths of approx. 300 m. The ULTIMAZ E25 is a consequent further development of the version ULTIMAZ P2P. The comfort features E25 is also designed for in-house installation of mini cables and fibres. The performance is improved and its handling is comfortable.

The battery operated electric drive enables an eight hours operation. The pushing force can be adapted electronically by the operator in six steps from 5 to 22 N. The correct pushing force is found out as usual by crash-tests. This precise adjustment of the pushing force is the basic principle to avoid damages to the delicate mini cables and fibres. The ease of use is increased by the automatic contact pressure of the driving roller system. The contact pressure is automatically determined in dependency of the adjusted pushing force. The maximum speed of 80-180 m/min. is also controlled electronically in dependency of the pushing force.

In in-house installation with micro ducts and due to many bows and with special fire protected cables high air pressure of 10-12 bar is necessary. Because of low air volume small manageable compressors (see below) or compressed air bottles are sufficient.

Accessory and performance see technical details below. Without cable and duct inserts, see accessory below.

UltimaZ P2P blow fibre units and micro cable blowing device especially for in-house cabling up to lengths of approx. 200 m. The UltimaZ P2P makes it possible to continue the last mile from the underground floor to all flats. Drive through an accu-driven hand-drill, accessory.

In in-house installation with micro ducts and due to many bows and with special fire protected cables high air pressure of 10-12 bar is necessary. Because of low air volume small manageable compressors (see below) or compressed air bottles are sufficient.

The torque can be adjusted by fine steps from 0-20 N. This avoids largely damages of the cables. Accessory and performance see technical details below. Without cable and duct inserts, see accessory and techn. details below.

Compressed air hose DN 10, L 7 m, with swing-coupling and connecting standard nipple for UltimaZ P2P to compressor VE 100

Air connector for connecting hose DLS 10/7 with a compressor

Air regulator with manometer for subduct calibration set.

With safety couplings for air pressure hoses.

Pressure wheels to P2P, D 40 mm, NBR-tyres or aluminium

Drive wheel to UltimaZ P2P, steel D 40, with groove.

Drive wheel to UltimaZ P2P, steel D 40, with groove.

Duct insert divisible for P2P, for duct-OD 3-12 mm and cable-Ø 1,8-4,0 mm, incl. 6 duct seals.

Cable insert divisible for UltimaZ P2P, for cable-Ø 1,0-4,0 mm, for cable lead in.

Duct insert not divisible for P2P, for duct-Od 3-12 mm and cable-Ø 1,8-4,0 mm, without sealing KAD.

Cable insert not divisible for UltimaZ P2P, for cable lead in.

Cable sealing-set to UltimaZ P2P, to RET 3018 up to RET 12040, sets of see table below

Lubricator for continuous greasing of the cables blown by UltimaZ P2P, by MicroJets PR/PRM 196. Performance and techn. details see below.

Micro Jetting Lube, lubricant for blowing-in fibre optic cables. Excellent lubricating effect. Adheres to the duct wall and leaves the cable nearly dry, an advantage for over blowing and working in cascades with further blowing machines. Consumption approx. 10 ml per 1000 m at duct-ID 10 mm. For other duct-ID analogue For lubrication unique and ultimate classification, Water pollution class - non-hazardous, acc. to VCI-Conception. Safety data sheets are available.

Sponge for sub duct cleaning and pre-lubricating prior to cable blowing

Compressor with electric motor for blowing-in optic bundle fibres and mini cables in in-house installation. 230 Volt, without after cooler. Portable and transportable on 2 wheels. Soundproof hood. Suitable for UltimaZ P2P.

Compressor with electric motor. For blowing-in fibre optic micro cables, fibres and bundle fibres. Mounted on 2 wheels, which enables the transport on stairs for one person alone. Suitable for UltimaZ P2P.

Cable drum unwinder for very small drums with one or two flanges. The unwinder can accommodate a wide variety of drums with a bore from 20 mm by combining different cones. Due to its low weight of only 6.4 kg, it is very handy and yet has a high stability. This makes it very safe to use, e.g. for in-house cabling.

Cable unwinder for small drums, even with damaged flanged wheels for electric installation works. Tubular steel construction galvanized. Consisting of: basic frame with 2 rubber coated wheels, one drum shaft D 25 mm with 2 cones of polyamide for hole diameter 25-80 mm.