SuperJet for tension-free blowing-in of bigger fibre optic cables and bundles of sub ducts D 7-14 mm each. A very long belt drive of 330 mm secures a correct guide of cables and sub ducts. With digital length and speed meter. Including hydraulic power pack with petrol engine and control instruments. Worldwide thousand fold proven blowing machine. For successful blowing-in of big length, in ducts of D 50 mm a compressor of 12 bar and 10 m³/min. is necessary. Basic machine without belts, cable and duct inserts. See accessory below. Basic equipment consist of the following details:
Petrol-hydraulic pack with hoses
Length- and speed meter
Ball valve 1 1/2" with screw couplings.
Air pressure hose 1 1/2", length 10 m.
Compressor of min. 10 m³/12 bar for duct dia. 50x4,6
Lubricator L 24 for automatic continuous greasing of the cable blown by Mini-, Intelli-, Cable- or SuperJet. This lubricator L 24 is especially recommended when blowing bigger cables in ducts 20 - 50 mm. Performance and technical details see below.
Article with accessory klick here!
The Lubricator L 24 guarantees an uniform lubrication on the whole length duct length.
With the Lubricator L 24 the blowing cable lengths can be increased of approx. 20-40 %.
This bigger Lubricator L 24 is only for use with Mini-, Intelli-, Cable- and SuperJet machines.
Y-duct connector for blowing-in a second or third cable in occupied ducts. Please select for this the corresponding cable and duct inserts. See table below of CableJet or SuperJet.
Allows to blow-in second or third cable in the same duct.
Also necessary for blowing of additional subducts in occupied ducts.
Flat rubber chain single incl. chain joint. This chain is mounted on the top to complete the existing chain of 5x7 / 5x10 / 5x12 and 3x16 for further subducts of 2x7 / 3x7 / 2x10 / 2x12 and 2x16 mm.
Cable inserts suitable to CableJet and SuperJet. Also necessary for the Y-piece to blow-in a second or third cable in one duct. One set of cable sealing for the hole range of cable diameters is included.
High powered compressors for blowing-in bigger fibre optic cables. Suitable for CableJet and SuperJet and for duct ID up to 41 mm. Mounted on single axle trailer with height adjustable overrun drawbar. Incl. Diesel-Oxidation filter and particle filter. Emission standard V and US-standard EPA Tier 4. Equipped with Telematics 36 @ Mobilair.
Drum transporting and unwinding stand for subduct drums of different suppliers. For several application e.g. on platforms of trucks or for placing on the ground or on the trailer TRA 8120, see below. Equipped with 2 lightweight aluminium shafts D 75 mm with 2 clamps and 6 spacer tubes.
Drum unwinding stand dismounted for shipment ex works. With small efforts the customer can screw it together. If not used for longer time, it can again be dismounted and stocked at a very small place.
Sturdy steel construction, hot galvanized, screw mounted, easy dismountable for transport.
Pay load for 8 / 6 full subduct drums, total weight without trailer 2500 kg possible.
Two crank spindles to lift the stand for unwind the subducts in any position.
Tandem trailer prepared for mounting the drum unwinding stand TRG 8120 or for universal use for other goods. Height adjustable draw bar with overrun and parking brake. With eye and interchangeable ball coupling. Two rear crank spindles. Chamber to lodge the aluminium loading ramps. accessory 4 folding down alu-boards and 2 aluminium loading ramps. Trailer checked by Technical Inspection Agency.
