Pulling-in units for subducts | and fibre optic cables

1 | Cutting unit

PDF-Sheet

To achieve a big packing density of subducts in pipes a subduct-bundle with many single ducts from only one single drum is pulled into the duct. The cover of the subduct-bundle is to cut open and to remove manual before the bundle is pulled in. This is done with the cutting unit for subduct bundles. Consisting of double knife, 8 leading rollers and leading tongue made of stainless steel.

With double knives, 8 leading rollers and tongue made of stainless steel.
Lead-in width 70, lead-in height 15-30

,Subduct-bundle-cutters,Subduct-cutting-unit,Subduct-pulling-heads,Cisaille-coupe-conduit-tube,Têtes-tirage-conduit-tube,Cortadores-paquetes-subductos,Cabezas-tiro-subductos

Code	Type	Dimension										kg
273905	SVR 70	480x330x290										30,10

2 | Sub duct pulling heads

PDF-Sheet

Subduct pulling heads for subduct bundles in short duct length. Pulling head of stainless steel, pulling eye of steel.

Important to meet the max. allowed pulling forces given by the producer.
Depending on the friction and allowed pull forces length to 300 m are possible.
At a high utilization of the duct volume the pulling lengths could be shorter.

,,,

Code	Type	Subducts	In centre	Head-D	D-ID	kg
2739513	ZK 24/07X	24 x D 7x1,50	1xD14,0x2,00	48,5	min. 51,0	0,85
2739533	ZK 18/07	18 x D 7x1,50	non	36,0	min. 40,8	0,59
2739535	ZK 14/07	14 x D 7x1,50	non	36,0	min. 40,8	0,51
2739543	ZK 10/07X	10 x D 7x1,50	1xD 14,0x2,00	35,0	min. 40,8	0,43
2739563	ZK 10/07	10 x D 7x1,50	non	28,5	min. 32,6	0,36
2739573	ZK 8/07X	8 x D 7x1,50	1xD 14,0x2,00	28,5	min. 32,6	0,22
2739575	ZK 6/07	6 x D 7x1,50	non	24,0	min. 27,4	0,27

3 | Sub duct pulling units

PDF-Sheet

Subduct pulling units for pulling of odd parts of subducts through shorter ducts. The pulling units are divisible and can be easily combined by the user in any configuration.

Consisting of screw link, ropes with brass nipples.
Mind the max. allowed pulling forces given by the producer of the subducts.
In consideration of friction and allowed pulling forces of the duct 300 m could be achieved.
At a high filling ration pulling lengths can be much shorter.

,,,

Code	Type	Subduct-D	D-OD	Subduct-D	D-OD	kg
2739795	ZE 7/0707	7 pcs. 7x0,75	from 32	---	---	0,14
2739797	ZE 7/1010	---	from 40	7 pcs. 10x2,00	from 40	0,37
2739801	ZE 1/1012	1 pcs. 10x1,00	from 32	1 pcs. 12x2,00	from 32	0,05
2739802	ZE 2/1012	2 pcs. 10x1,00	from 32	2 pcs. 12x2,00	from 32	0,08
2739803	ZE 3/1012	3 pcs. 10x1,00	from 32	3 pcs. 12x2,00	from 40	0,11
2739804	ZE 4/1012	4 pcs. 10x1,00	from 40	4 pcs. 12x2,00	from 40	0,14
2739805	ZE 5/1012	5 pcs. 10x1,00	from 40	5 pcs. 12x2,00	from 50	0,17
2739807	ZE 7/1012	7 pcs. 10x1,00	from 40	7 pcs. 12x2,00	from 50	0,23
2739808	ZE 8/1012	8 pcs. 10x1,00	from 50	8 pcs. 12x2,00	from 63	0,26
2739811	ZE 1/1214	1 pcs. 12x1,10	from 32	1 pcs. 14x2,00	from 32	0,06
2739812	ZE 2/1214	2 pcs. 12x1,10	from 32	2 pcs. 14x2,00	from 40	0,10
2739813	ZE 3/1214	3 pcs. 12x1,10	from 32	3 pcs. 14x2,00	from 40	0,14
2739814	ZE 4/1214	4 pcs. 12x1,10	from 40	4 pcs. 14x2,00	from 50	0,18
2739815	ZE 5/1214	5 pcs. 12x1,10	from 50	5 pcs. 14x2,00	from 63	0,22
2739817	ZE 7/1214	7 pcs. 12x1,10	from 50	7 pcs. 14x2,00	from 63	0,30
2739823	ZE 3/1414	3 pcs. 14x1,30	from 50	---	---	0,19
2739827	ZE 7/1414	7 pcs. 14x1,30	from 63	---	---	0,39
2739831	ZE 1/1616	1 pcs. 16x2,00	from 32	---	---	0,20
2739833	ZE 3/1616	3 pcs. 16x2,00	from 63	---	---	0,35
2739834	ZE 4/1616	4 pcs. 16x2,00	from 63	---	---	0,50
2739838	ZE 8/1616	8 pcs. 16x2,00	from 75	---	---	0,61
2739843	ZE 4/2025	4 pcs. 20x2,50	from 75	---	---	0,60
2739850	ZE 4/2020	4 pcs. 20x2,00	from 75	---	---	0,54

4 | Plug and pulling head

PDF-Sheet

Plug, blowing and pulling head of aluminium for subducts

,,,

Code	Type	For D-D	Set of	Size	kg
2739904	SDV 0707	7x0,75	10	D 7,2x44	0,51
2739908	SDV 0715	7x1,50	10	D 7,2x40	0,03
2739912	SDV 1010	10x1,00	10	D 10,2x50	0,22
2739914	SDV 1211	12x1,10	5	D 12,2x50	0,06
2739922	SDV 1413	14x1,30	5	D 14,2x50	0,08
2739928	SDV 1620	16x20	5	D 16,2x56	0,21

5 | Cable shaft entrance roller

PDF-Sheet

Cable shaft entrance roller bow, without or with base support. Roller bow 45°, Radius 600 mm, for fibre optic cables, steel construction galvanized with 4 polyamide rollers with ball bearings, diam. 80/30x50 mm.

,,,

Code	Type	Device	Bow	kg
274020	LRB 45	Roller bow, without support	45°, R 600	3,60
274060	LSE 4	Shaft entrance roller with base support	45°, R 600	7,30

6 | Cable lead-in roller

PDF-Sheet

Cable lead-in roller for protection of the cable and the duct. With steel tubes galvanized with fixing clamp to the duct.

,,,

Code	Type	D-ID	Tube-L	Roller-D	kg
274420	LER 22/1	22	240	80/30x38/50	0,60
274430	LER 25/1	25	240	80/30x38/50	0,70
274440	LER 28/1	28	240	80/30x38/50	0,70
274470	LER 35/1	35	240	80/30x38/50	0,82
274490	LER 40/1	40	240	80/30x38/50	0,80
274530	LER 54/1	54	240	80/30x38/50	0,90
274580	LER 74/1	74	240	80/30x38/50	1,20

7 | Conduit cutters

PDF-Sheet

Conduit cutters for plain cuts.

,,,

Code	Type	D-OD	Length	kg
273171	MRS 43	to 42	215	0,45
273172	MRS 50	to 50	265	0,60
273173	MRS 63	to 63	285	0,70
273174	MRS 75	to 75	485	1,60

8 | Burring tools

PDF-Sheet

Burring tools for in- and outside of plastic conduits.

Paring knife MSM 40, for separating multiple conduits.

,,,

Code	Type	D-OD	Burring	Mat.	kg
273185	MRA 63	20-63	only extern	Poly.	0,25
273180	MRE 50	28-50	ext. /intern	Alu	0,43
273200	MSM 40	Paring knife	---	Steel	0,50

9 | Conduit and cable slitter

PDF-Sheet

Conduit slitter for lengthwise and circumferential slitting of plastic conduits and cable covers. Complete reinforced steel version. In case 195x75x45 mm.

,,,

Code	Type	To wall thickn.	L/W/H mm	kg
255905	KMS 6	6	195x75x45	0,35
255910	ERM 6	Spare knife	---	0,03

10 | Subduct cutter

PDF-Sheet

Subduct cutter for occupied or empty subducts.

,,,

Code	Type	D-OD	For subducts									kg
272400	SDC 0314	3-12	occupied+empty									0,02

11 | Subduct cutter

PDF-Sheet

Subduct cutter for occupied or empty subducts.

,,,

Code	Type	D-OD	For subducts									kg
272402	SDC 1420	14/16/20	occupied + empty									0,07

12 | Subduct cutting tongs

PDF-Sheet

Subduct cutting tongs, only for use with empty subducts.

,,,

Code	Type	D-OD	For subducts	kg
272410	RSK 0214	2-14	only for empty subducts	0,10
0931240272	EM 14	--	5 spare blades for RSK 0214	0,03

13 | Subduct cutting tongs

PDF-Sheet

Duct cutting tongs, only for use with empty subducts.

,,,

Code	Type	D-OD	For subducts	kg
272420	RSK 0420	4-20	only for empty subducts	0,20
027242110	EM 20	--	Spare blade for RSK 0420	0,05

14 | Subduct cutting tongs

PDF-Sheet

If the cross-section of a microtube is altered, the DuctDoc helps to return the microtube to its original shape with a round cross-section. Applicable for ID: 3.5 / 4 / 5.5 / 6 / 8 / 10 / 11.4 / 12 / 13 / 15 / 16 mm

,,,

Code	Type	D-OD	For subducts									kg
272435	MKD 3516	see above	only for empty subducts									0,11

15 | Burring tool

PDF-Sheet

Burring tool for in- and outside of plastic conduits. Of lightweight aluminium

,,,

Code	Type	D-OD	Dimension									kg
273175	MRE 26	3-26	D 36x90									0,39