Conduit cutters for plain cuts.

Burring tools for in- and outside of plastic conduits.

Paring knife MSM 40, for separating multiple conduits.

Conduit slitter for lengthwise and circumferential slitting of plastic conduits and cable covers. Complete reinforced steel version. In case 195x75x45 mm.

This cable conduit saw SRS 6.1 is a further development of the proven SRS 6. The saw is suitable for cutting occupied and unoccupied cable conduits without damaging internal cables or subducts. The saw is suitable for conduits at an outer diameter of 32-150 mm and at a max. wall thickness up to 6 mm. The saw can precisely cut lengthwise and crosswise and can also precisely cut windows into the cable conduit. Especially for long cuts on the cable conduits which are necessary for cable line redirections the great benefits of this saw pay off.

The cutting depth can be precisely adjusted to a 1/10 of a millimetre by an adjustment mechanism thus the cables inside the cable conduit are well-protected. The cutting depth has always to be set 0,2 mm less than the conduits wall thickness. The remaining very thin plastic membrane will be removed by a lifter tool thus the cable is also protected during this final step. The conduit guiding plates allow a high safety at work as well as accurate cuts. The guiding plates are available for the below mentioned conduit-diameters. The cordless saw is handy and small in order to be fit for application also in narrow working conditions its weight is below 2 kg. Included in delivery are the following parts:

Jettinglube lubricant for blowing-in fibre optic cables. Excellent lubricating effect. Adheres to the duct wall and leaves the cable nearly dry, an advantage for over blowing and working in cascades with further blowing machines. Consumption approx. 0,5 l per 1000 m at duct-ID 40 mm. For other duct-ID analogue

For lubrication unique and ultimate classification, Water pollution class - non-hazardous, acc. to VCI-Conception. Safety data sheets are available.

Cable lubricant Softenol, liquid, for blowing-in and for pulling-in fibre optic cables.

For lubrication unique and ultimate classification, Water pollution class - non-hazardous, acc. to VCI-Conception. Safety data sheets are available.

Sponge for duct cleaning and pre-lubricating prior to cable blowing

The new pressure test device combines three test methods in one electronic device. General test rules” individual selectable acc. requirements from the customer - The requirement from Deutsche Telekom acc. “ZTV-TKNETZ 40” - The low-pressure test acc. EN 1610:2015 as well as worksheet DWA-A-139:2009

The high-pressure test is presently the most frequent test method in the range of pressure tests for protective ducts. This test method will be performed at thick-walled protective ducts and subducts (micro ducts). With regards to the protective ducts, ducts with OD 50/40/32 mm are most frequently used application. For subducts a wider range of ducts can be tested from 7x1,5 until 20x2,5 mm. The high-pressure test distinguish between two different targets:

The DPG 17U Universal pressure test device for test of cable ducts with regards to protective ducts and subducts working in the range of 0…7 bar. The operation is made by a 7” colour-graphic-touch display. The new device support the user through a simple and menu-driven operation. With the help of a matrix (table) three different test methods can be selected. Those are “General test rules” individual selectable acc. requirements from the customer, the requirement from Deutsche Telekom acc. “ZTV-TKNETZ 40” and the low-pressure test acc. “EN 1610:2015”. This results in a maximum support for the user.

The result of the pressure test is summarized in a clear test protocol with three core areas. The test protocol will be stored on the device and can be loaded by a USB-interface to a customary PC. ?
The left shown 1. protocol shows a passed test “Test criteria fulfilled” ?
The left shown 2. protocol shows a failed test “Test criteria not fulfilled”

Pressure test distribution units for high-pressure tests of 1 duct OD 7 to 110 mm for protective ducts and subducts (micro ducts).

With regards to the protective ducts the 50x4.6 duct is the most frequently used application. For subducts a wider range of ducts can be tested from 7x1.5 until 20x2.5 mm. For the connection of the ducts the right accessories have to be used to perform the test.

Pressure test distribution units for high-pressure tests of ducts OD 20 to 110 mm, for 4 protective ducts or 4 subducts (micro ducts).

With regards to the protective ducts the 50x4.6 duct is the most frequently used application. For subducts the dimension 20x2.5 mm can be tested. For the connection of the ducts the right accessories have to be used to perform the test.

Pressure test distribution units for high-pressure tests of 1-12 subducts (micro ducts).

A wider range of subducts can be tested from 7x1.5 until 20x2.5 mm. For the connection of the ducts the right accessories have to be used to perform the test.

Reducing coupling D 10-7, with duct 10x2/100, for D-OD 7 mm, for coupling subduct OD 7 mm with pressure test distribution units DPV 12, necessary to order 275750 DAK 10.

Air connectors for subduct calibration sets and for high pressure test units.

Conduit plug for fixing on duct-OD with hose safety coupling applicable for duct calibration, duct pressure tests, duct cleaning etc.

Connection coupling for subducts, made of steel, plug-in type, for distribution device DPV 12

Duct plug of plastic , 0-7 bar, for subducts D 5-20 mm

Testing manometer 10 bar, as end section of cable conduits, for high pressure tests, with safety coupling 42 mm. For air distribution devices DPV 1 + DPV 4. Max. air pressure 7 bar. To apply with conduit plugs KRA 20-110.

Testing manometer 10 bar, as end section of subducts for high pressure tests, with safety coupling NW 7,4. For air distribution devices DPV 12. Max. air pressure 7 bar. To apply with conduit plugs AKS 10-20.

Case for accessory of high pressure test devices, without parts, with 12 shelves as following:

Conduit calibration and leakage-test unit. Calibration and leakage-test before starting the cable blowing-in procedure is the safest guarantee for successful installation of fibre optic cables. Unit consisting of:

Supplementary extension set for calibration and leakage test unit.

Calibre housings of polyamide with sleeve rings, without transmitter. Calibre length 145 mm, total length 250 mm

Miniature transmitter D 18x88 mm, incl. battery, suitable for all a. m. calibres.

Pistons for loosing old cables in ducts before blowing or pulling them out.

Conduit plug for fixing on duct-OD with hose safety coupling applicable for duct calibration, duct pressure tests, duct cleaning etc.

Conduit sealing plug applicable for duct pressure tests.

Shut-off bladders to lock off the pipeline to be tested. Shut-off bladders are used on the opposite side of the test location. The short dimensions of the Mini version allow space-saving installation of pipe bends also.

Test bladders Mini for testing and shutting off pipes for low pressure testing.

Air coupling (brass) standard for bladder extension. Air coupling (chromed) special CE-standard 10.4 mm, for inflating the duct.

Foot pump with double stroke and safety valve 2.5 bar to inflate SBM shut-off bladders and PBM test bladders. The use of a second foot pump for the second pipe end saves considerable installation time.