FOC unwinding equipment
1 | Cable unwinder
Cable drum unwinder for very small drums with one or two flanges. The unwinder can accommodate a wide variety of drums with a bore from 20 mm by combining different cones. Due to its low weight of only 6.4 kg, it is very handy and yet has a high stability. This makes it very safe to use, e.g. for in-house cabling.
- For drum D up to 300 mm and drum width up to 220 mm, weight max. 5 kg
- Clamping bearings for easy running and small pull-off forces
- All cones are included and attached to the unit
2 | Cable unwinder
Cable unwinder for small drums, even with damaged flanged wheels for electric installation works. Tubular steel construction galvanized. Consisting of: basic frame with 2 rubber coated wheels, one drum shaft D 25 mm with 2 cones of polyamide for hole diameter 25-80 mm.
- Collapsible for easy transportation to the site.
- Easy movable with the drum through big rubber coated wheels.
- For drum-D to 800 and drum widths to 530, drum weight max. 200 kg
- As accessory steel tube drum shaft D 50, ball bearings, 2 clamps, for cones see table below.
3 | Drum unwinding stand for FOC
Drum unwinding stand for FOC or subduct drums, galvanized. Equipped with a lightweight aluminium shaft D 75 mm with drum shaft securing and 2 clamps.
- Sturdy steel construction, hot galvanized, easy dismountable by hand for transportation.
- Two crank spindles to lift the stand for unwind cables in any position.
- High stability under load even in uneven places.
- For drum-D to 1400, and drum width to 900, drum weight max. 500 kg.
- As accessory alu-drum shaft D 50, ball bearings, order clamps and cones separately, see table below.
- Dimensions mounted: L/W/H 1450/1400/689.
4 | Cable trailer straight or adjustable drawbar
Cable drum trailer with straight or height adjustable draw bar and overrun brake for speeds up to 80 km/h. For loading the support arms are swung down and then raised picking up the drum by a single hand winch. Rotatable aluminium shaft as accessory, see below
Payload without accessories. If accessories are mounted like hydr. drum drives etc. the payload reduces according to their weights.
- Types G - with straight draw bar can only be equipped with ball coupling
- Types H - with adjustable draw bar equipped with eye coupling, ball coupling as accessory
- Suitable for one-man operation
- Complete trailer hot galvanized
- Rotating alu shafts as accessory, please order shaft clamps separately.
- Drum band brake as accessory, see below.
- Position lighting at the front of the cable drum trailer
5 | Rotating drum shafts
Surcharge for rotating drum shafts. The standard trailers listed above are delivered without shaft as standard. With rotating shafts cable drums unwind much easier, they are necessary if the trailer is equipped with a drum drive or a drum disc brake.
6 | Rear protection gate
Rear protection gate, for Cable trailers KVS 1000-2000 G+H, hot galvanized.
The need of a rear protection is subject to national regulations. Independent of this, the rear protection offers a higher safety in the road traffic.
7 | Ball coupling
8 | Cable drum band brake
9 | Drum drive one side
Drum drive one side for cable trailers KVS 1000-2000/80, but not suitable for all types, see table below. Hydraulic or pneumatic, without hoses and power packs.
10 | Hydraulic power pack mobile
Hydraulic power pack for cable drum drive, with petrol- or Diesel engine equipped with rapid hose couplings. Oil presser 160 bar, tank 10 Litre, oil flow 12 l/min. l/min.
- The hydraulic power pack must not be mounted on drawing bar of the trailer, the hitch load would be to high.
- For control of the winding speed please order below mentioned hydraulic hose combination
11 | Hydraulic hose set
