Blowing units semi-automatic for bundle fibres, micro-cables and small mini-cables
1 | Duct single sealing to intermediate blowing head and Lubricator
2 | OptiJet™ Reporting
The most innovative and compact semi-automatic cable blowing unit for bundle fibres, micro-cables and small mini-cables.
The new OptiJet?"? Reporting is a powerful, smart and pioneering blowing unit that sets new standards in the blowing of fi-bre-optic micro-cables and mini-cables as well as bundle fibres. It can blow cable diameters of 1.5 to 8.0 mm into duct out-er diameters of 5 to 16 mm with a pushing force of maximum 150 N. The OptiJet?"? Reporting ensures maximum cable lay-ing quality, provides optimum operator support and requires less experience, to the benefit of both cable layers and cli-ents.
The new belt drive system allows uniform power transfer to the cable and guarantees optimum cable protection. The auto-matic crash test function is an absolute innovation. The OptiJet?"? Reporting provides the operator with maximum support in this and makes the crash test a simple and fast routine. This objective measurement of the maximum pushing force relieves the operator of the responsibility for subjective cable damage assessment and thus guarantees a high level of protection against such damage. The unit monitors important parameters for cable protection, such as pushing force and cable slip-page, during cable installation.
Its new drive technology using electric motors in combination with a self-sufficient battery system facilitates quiet working. The compressor's entire air output can thus be used for laying the cable.
Also new is the wireless, robust IP68 industry tablet with intuitive user interface.
Combined cable/duct inserts reduce the number of accessories, simplify conversion and significantly shorten conversion times.
Precise and clear logging of the agreed blowing services facilitates error detection in the event of an accident, billing and data backup.
The new OptiJet?"? Reporting is a powerful, smart and pioneering blowing unit that sets new standards in the blowing of fi-bre-optic micro-cables and mini-cables as well as bundle fibres. It can blow cable diameters of 1.5 to 8.0 mm into duct out-er diameters of 5 to 16 mm with a pushing force of maximum 150 N. The OptiJet?"? Reporting ensures maximum cable lay-ing quality, provides optimum operator support and requires less experience, to the benefit of both cable layers and cli-ents.
The new belt drive system allows uniform power transfer to the cable and guarantees optimum cable protection. The auto-matic crash test function is an absolute innovation. The OptiJet?"? Reporting provides the operator with maximum support in this and makes the crash test a simple and fast routine. This objective measurement of the maximum pushing force relieves the operator of the responsibility for subjective cable damage assessment and thus guarantees a high level of protection against such damage. The unit monitors important parameters for cable protection, such as pushing force and cable slip-page, during cable installation.
Its new drive technology using electric motors in combination with a self-sufficient battery system facilitates quiet working. The compressor's entire air output can thus be used for laying the cable.
Also new is the wireless, robust IP68 industry tablet with intuitive user interface.
Combined cable/duct inserts reduce the number of accessories, simplify conversion and significantly shorten conversion times.
Precise and clear logging of the agreed blowing services facilitates error detection in the event of an accident, billing and data backup.
- Inputs for the blowing procedure and configuration of the machine via touch display
- Favourites with the essential laying parameters allow faster work
- Display of the entire blowing procedure and subsequent creation of blowing logs in PDF format
- Wireless export via WIFI/Bluetooth or through other platforms (e-mail, etc.) using a SIM card
- The assistance systems and partial automation help operators with less experience to blow successfully. The issue of currently tight labour markets can thus be alleviated.
- Simple, quick and automated performance of the crash test
- Cable protection thanks to belt drive, display and the monitoring of critical parameters
- Automatic logging and easy transmission of the logs
- Significantly simplified handling and maximum operator support
- Proven and commonly used battery system using brand-name batteries
3 | OptiJet™
Please note the following:
The OptiJet?"? can not be upgraded to an OptiJet?"? Reporting.
This unit cannot be used for logging.
The OptiJet?"? can blow cable diameters of 1.5 to 8.0 mm into duct outer diameters of 5 to 16 mm with a pushing force of maximum 150 N. The OptiJet?"? guarantees maximum cable laying quality and optimum cable protection thanks to the new belt drive system.
The main benefits for cable layers:
The OptiJet?"? can not be upgraded to an OptiJet?"? Reporting.
This unit cannot be used for logging.
The OptiJet?"? can blow cable diameters of 1.5 to 8.0 mm into duct outer diameters of 5 to 16 mm with a pushing force of maximum 150 N. The OptiJet?"? guarantees maximum cable laying quality and optimum cable protection thanks to the new belt drive system.
The main benefits for cable layers:
- Electric motor driv enables quiet working and the full air output of the compressor can be used for laying the cable
- Self sufficient battery system
- The assistance systems and partial automation help operators with less experience to blow successfully. The issue of currently tight labour markets can thus be alleviated
- Automated performance of the crash test
- The assistance systems and partial automation help operators with less experience to blow successfully. The issue of currently tight labour markets can thus be alleviated.
- Cable protection thanks to belt drive, display and the monitoring of critical parameters (pushing force, slippage)
- Proven and commonly used battery system uisng brand-name batteries
- Working with innovative technology
- Reduced number of accessories, simplified conversion, shorter conversion times
4 | OptiJet accessory set
5 | OptiJet external power supply
6 | OptiJet battery pack
Backpack battery with the power of approx. 5.5 individual 18 V/6 Ah batteries. With charge level indicator, ON/OFF button and charger. Using an additional adapter and without having to interrupt operation, it can be connected to the charging socket of the OptiJet to considerably increase the available blowing time.
The adapter for the charging socket on the OptiJet, item no. 424.514, is required for this.
Technical data:
The adapter for the charging socket on the OptiJet, item no. 424.514, is required for this.
Technical data:
- Battery: Lithium-ion
- Voltage: 2x 18 V/40 V
- Power output: 33,5 Ah (1,200 Wh)
- Charging time: 360 min. (charger included in the scope of supply)
- Dimensions: 369 x 261 x 139 mm
7 | Additional batteries
Additional 18 V/6.0 Ah lithium-ion batteries, on top of the batteries supplied as standard with OptiJet/OptiJet?"? Reporting.
Attention: It is recommended to always order two batteries, as the OptiJet is powered by two batteries.
As standard, the OptiJet?"? Reporting is delivered with 4 batteries.
Attention: It is recommended to always order two batteries, as the OptiJet is powered by two batteries.
As standard, the OptiJet?"? Reporting is delivered with 4 batteries.
8 | OptiJet accessory sets
OptiJet accessory set. All cable/duct inserts as well as 6 cable and duct seals each according to below table.
Belts for cable diameters 1.5 to 3.0 mm and 3.1 to 8.0 mm are included as standard in the OptiJets scope of supply.
Separately available cable/duct inserts: REO 52, REO 53, REO 74, REO 123
Belts for cable diameters 1.5 to 3.0 mm and 3.1 to 8.0 mm are included as standard in the OptiJets scope of supply.
Separately available cable/duct inserts: REO 52, REO 53, REO 74, REO 123
9 | Seperately available OptiJet cable/duct inserts
Combined OptiJet cable/duct inserts for duct and cable diameters according to table. (incl. 6 duct seals each)
10 | Seperately available OptiJet cable guides
11 | Cable sealing
Cable sealings suitable for cable blowing machines and cable-diam. according to table shown below.
12 | Duct sealing
13 | Compressor diesel engine
High powered compressors for blowing-in bigger fibre optic cables. Suitable for MiniJet, for duct ID up to 41 mm. Mounted on single axle trailer with height adjustable drawbar, without overrun brake.
- Hatz Diesel-engine, 42 kW. Compressor dimension: 4000x1540x1445 mm.
- Flow rate 3,8 m³, at 14 bar working pressure
- With integrated after cooler and water separator.
- Air discharge valve: 2 x G 3/4"
14 | Compressor diesel engine
High powered compressors for blowing-in bigger fibre optic cables. Suitable for MiniJet, for duct ID up to 20 mm. Mounted on single axle trailer with height adjustable drawbar, without overrun brake.
- Kubota Diesel-engine, 17,9 kW. Compressor dimension: 3245x1260x1330 mm.
- Flow rate 1,6 m³, at 14 bar working pressure.
- With integrated after cooler and water separator.
- Air discharge valve: 2 x G 3/4" (shown with option EVK 34)
15 | Compressor petrol engine
Compressor with petrol engine and after cooler. For blowing-in fibre optic mini cables, fibres and bundle fibres. Suitable for all MicroJets and for MiniJet P 02. The external after cooler reduces the compressed air temperature approx. 8° C above ambient temperature. The compressor is equipped with a sound absorption cover. It is portable by two pneumatic wheels.
- With Honda-petrol engine 15,50 kW. Dimension: 1080x800x796
- Flow rate 1000 l/min. at 15,0 bar working pressure.
- With separate after cooler electrical feeded by the compressor. Air discharge valve: 1 x G 3/4"
- As accessory see tiltable support for after cooler, table below.
16 | Compressor petrol engine with mounting frame for after cooler
Compressor with petrol engine and after cooler. For blowing-in fibre optic mini cables, fibres and bundle fibres. Suitable for all MicroJets and for MiniJet P 02. The external after cooler reduces the compressed air temperature approx. 8° C above ambient temperature. The compressor is equipped with a sound absorption cover. It is portable by two pneumatic wheels.
- With Honda-petrol engine 15,50 kW. Dimension: 1080x800x796
- Flow rate 1000 l/min. at 15,0 bar working pressure.
- With separate after cooler electrical feeded by the compressor. Air discharge valve: 1 x G 3/4"
- inclusive folding mounting frame for aftercooler, see next table below.
17 | Support for after cooler
Support for the after cooler on compressor MK 17.4. Steel frame hot galvanized. With this the after cooler is fixed safe and rubbery-elastic by four elements.
To transport the compressor in a van the after cooler is tiltable, please mind the total height of approx. 1,10 m. The after cooler can easily be dismounted from the support.
- Dimension with vertical positioned after cooler, L/W/H 1170/800/1220
- Dimension for transportation with tilted after cooler, total height only 1100
18 | Compressor electric motor
Compressor with electric motor. For blowing-in fibre optic micro cables, fibres and bundle fibres. Mounted on 2 wheels, which enables the transport on stairs for one person alone. Suitable for UltimaZ P2P.
- Electric motor 1,5 kW, 230 Volt, compressor dimensions: 570/440/1050 mm.
- Sound insulation bonnet, sound pressure level 79 dB(A).
- Constant, infinitely adjustable delivery pressure due to new piston compressor principle.
- Oil-free operation, no oil change, no check, oil- and water-free air.
19 | Lubricator L 9 - automatic device
Lubricator L 9 for continuous greasing of the cables blown by MicroJet, MiniJet and UltimaZ. Performance and techn. details see below.
Article with accessory klick here!
- The Lubricator guarantees an uniform lubrication on the whole duct length.
- To mount on MiniJet there are adapters, see below.
- In the Lubricator is included an adapter for the MicroJets EM 25, PR 140 and PRM 196
20 | Lubricant for FOC
Micro Jetting Lube, lubricant for blowing-in fibre optic cables. Excellent lubricating effect. Adheres to the duct wall and leaves the cable nearly dry, an advantage for over blowing and working in cascades with further blowing machines. Consumption approx. 10 ml per 1000 m at duct-ID 10 mm. For other duct-ID analogue
For lubrication unique and ultimate classification, Water pollution class - non-hazardous, acc. to VCI-Conception. Safety data sheets are available.
21 | Duct cleaning sponge
Sponge for sub duct cleaning and pre-lubricating prior to cable blowing
22 | Intermediate cable blowing head
Intermediate blowing head for finishing the left loops after blowing in two direction. Without duct inserts, without cable sealing. Max. pressure 16 bars.
23 | Duct inserts for Lubricator and intermediate blowing head
Duct inserts with 2 sealing for Lubricator and intermediate blowing head for duct-D see table below.
24 | Duct single sealing to intermediate blowing head and Lubricator
Duct single sealing to intermediate blowing head and Lubricator, for ducts-D see table below.
25 | Cable unwinder
Cable drum unwinder for very small drums with one or two flanges. The unwinder can accommodate a wide variety of drums with a bore from 20 mm by combining different cones. Due to its low weight of only 6.4 kg, it is very handy and yet has a high stability. This makes it very safe to use, e.g. for in-house cabling.
- For drum D up to 300 mm and drum width up to 220 mm, weight max. 5 kg
- Clamping bearings for easy running and small pull-off forces
- All cones are included and attached to the unit
26 | Cable unwinder
Cable unwinder for small drums, even with damaged flanged wheels for electric installation works. Tubular steel construction galvanized. Consisting of: basic frame with 2 rubber coated wheels, one drum shaft D 25 mm with 2 cones of polyamide for hole diameter 25-80 mm.
- Collapsible for easy transportation to the site.
- Easy movable with the drum through big rubber coated wheels.
- For drum-D to 800 and drum widths to 530, drum weight max. 200 kg
- As accessory steel tube drum shaft D 50, ball bearings, 2 clamps, for cones see table below.
27 | Drum unwinding stand for FOC
Drum unwinding stand for FOC or subduct drums, galvanized. Equipped with a lightweight aluminium shaft D 75 mm with drum shaft securing and 2 clamps.
- Sturdy steel construction, hot galvanized, easy dismountable by hand for transportation.
- Two crank spindles to lift the stand for unwind cables in any position.
- High stability under load even in uneven places.
- For drum-D to 1400, and drum width to 900, drum weight max. 500 kg.
- As accessory alu-drum shaft D 50, ball bearings, order clamps and cones separately, see table below.
- Dimensions mounted: L/W/H 1450/1400/689.
28 | Compressor electric motor
Compressor with electric motor for blowing-in optic bundle fibres and mini cables in in-house installation. 230 Volt, without after cooler. Portable and transportable on 2 wheels. Soundproof hood. Suitable for UltimaZ P2P.
- Electric motor 1,1 kW, 230 Volt, compressor dimensions: 560/350/560
- Capacity 100 l/min. at 12 bar.
- Soundproof hood 71 dB(A).
- Pressure reservoir 4 litre
29 | Compressed air hose
30 | Y-piece with accessory
Y-piece for connection of 2 compressors VE 100, with same pressure and volume of 15 bar and 0,24m³/min. Incl. 2 non-return valves. Connection parts are not included, the need is as following:
- For duct-Ø 10 - Code 275.766, DAM 10, Air-connector
- For duct-Ø 12 - Code 275.768, DAM 12, Air-connector
- For compressor connection: 2 air hoses Code 0423.340.15, DLS 10/7, see below