1 | Subduct calibration sets
The calibration sets MKV 0810 and MKV 1116 in conjunction with the micro- transmitter SKS 6 (code-no. 231940) are destined for the calibration of subducts with an internal diameter 8,0 to 16,0 mm. The calibration can be done for single subducts as well as for multi subducts. By the calibration defects or blockages on the subducts can be detected in advance thus a good blowing-in performance can be achieved.
 
The MKV 0810 set contains two calibres with different diameters for the calibration of subducts with internal diameter 8,0 or 9,8-10,0 mm. The MKV 1116 set contains three different calibres for testing subducts of ID 11,4-16,0 mm. The calibres are easily screwed onto the micro-transmitter and blown through the subducts by air-pressure. The set also contains all essential connectors, reducing nipples as well as a catcher for the micro-transmitter. The catcher has to be used in order to avoid damages to the micro-transmitter. The air-pressure for the calibration has to be limited to max. 4 bars for MKV 0810 and to max. 2 bars for MKV 1116. By applying a higher pressure the micro-transmitter might be damaged by hitting duct blockages or by hard crashing into the catcher at the very end. The set contains the following parts:
  • MKV 0810 with: each 3 calibre D 6,8 for ID 8,0 / 3 calibre D 8,5 for ID 9,8-10
  • MKV 1116 with: each 3 calibre D 9,5 / ID 11,4-12 / 3 calibre D 11,0 / ID 15-16 / 3 calibre D 12,5 / ID 15-16.
  • 6 washers to each calibre
  • 5 sponges for each calibre. 1 general catcher and different connectors and duct-reducers
  • Depending on the duct diameters different air connectors are necessary, see the following tables.
  • SKS 06, Detection frequency 33 kHz, detection depth in the ground max. 2,0 m
,,,
,,,
,,,
,,,
CodeTypeDevice Subduct-ID Case kg
231950 MKV 0810Calibration set 8-10 180x140x80 1,43
231952 MKV 1116Calibration set 11,4-16 442x357x151 5,00
231941 SKS 06Micro transmitter D 6,5x84 --- 0,17
231943 BAT 06Set of batteries 10 each --- 0,04
2 | Calibration Set for Subducts 10/06
The calibration set MKK 0606 in conjunction with the micro transmitter SKS 04 is foreseen to calibrate subducts with inner diameter D 6.0 mm only. The calibration can be performed for single subducts as well as for multi subducts in buried and protective pipe installed versions. This new calibration set supports the blowing-in of mini- and micro cables on a completely new level since the quality of a sub duct installation can be checked in general.

The set comprises of 3 calibres with protection sponge having a diameter of 4.8 mm, a collecting device for the pipe end, a spare battery cover and 2 spare batteries.
 
The calibre will be simply unscrewed on the micro transmitter and with the sponge ahead blown-into the pipes using compressed air. The micro transmitter is a precision engineered measuring device, which has to be handled in the civil engineering with special care. Never operate the transmitter without protection sponge, bumper and collecting device fixed at the end of the pipe. Attentions should be paid to max. possible bending radius and air injection pressure - too high air pressure can cause damages on the calibration set.

During backward blowing the enclosed collecting device has to be used or at least a sufficient padding of another collecting device shall be implemented.
  • Calibration set MKK 0606 including 3 calibres D 4,8 for ID 6,0 mm
  • 20 sponges and collecting device at the pipe end for collection of the calibre
  • 1 Micro Transmitter SKS 04, detection frequency 33 kHz, sensitivity in earth max. 2,0 m
  • Max. injection pressure 5 bar, 4 bar is sufficient for horizontal routes
  • Min. bending radius for subducts 175 mm, smaller radius cause unavoidable a blockage
  • Batteries of the larger micro transmitter SKS 06 are used
,Air-regulator,Pressure-reducing,Pressure-release,Cable-basket,Figarino,MicroLube,Cable-crash-tube,Cable-blow-in-stop,Cable-guides,Cable-tips,Duct-pipe-calibration-set,Conduit-duct-calibre,Conduit-duct-saw,Jeux-calibrage-tubes-conduites,Mandrins-calibres-conduites,Cisaille-coupe-conduites-tubes,Scie-circulaire-tube,Détecteur-câbles,Localisateur-câbles,Emetteur-conduites-tubes,Sonde-conduites-tubes,Essai-pression-conduites-tubes,Test-d'étanchéité-tubes,Juego-calibres-tubos,Cortadores-tubos,Sierra-circular-tubos,Tronzadoras-tubos,Detector-emisor-tubos,Localizador-cables,Comprobación-impresión-estanqueidad-tubos
,,,
CodeTypeDevice Subduct-ID Case kg
231930 MKK 0606Calibration set 6,0 180x140x80 1,00
231943 BAT 06Set of batteries 10 pcs. -- 0,04
3 | Detection of multi ducts with average duct in the centre
Multi ducts can be detected in short distances through the average duct of dia. 12x2,0 or 14x2,0 mm laying in the centre. The micro transmitter SKS 06 of diam. 6,4 mm is screwed on the M5 thread of the mini-rod diam. 3 mm. The obtainable pushing length depends on the local condition but is limited anyway by the max. length of the mini rod of 50 m. Using lubricant relieves pushing and pulling back the transmitter. Detection depth in the ground is max. 2 m. The yellow or red mini rod can be used for inserting the micro transmitter.

,,,
,,,
CodeTypeDevice Subduct-ID kg
231941 SKS 06Micro transmitter from 8 0,17
231943 BAT 06Battery set --- 0,04
4 | Detector for micro transmitter in subducts
Detector with 8 batteries, without transmitter. For precise localisation of non-metallic conduits, and to find blockages with the conduit rods yellow or red D 3,0 mm. The following configuration is possible:
  • Yellow conduit rod with screwed on micro transmitter for spot or blockage detection
,,,
CodeTypeFrequency Transmitter L/W/H mm kg
231611 CAT4+33 kHz, without 255/70/725 2,20
5 | FigarinO the cable basket
FigarinO. The FOC basket is used if the cable is to long to be blown completely with only one blowing machine. When half of the cable is installed in one direction the remaining cable is pushed into the FigarinO with the blowing machine. Out of the FigarinO this part of the cable can be blown uncut in the opposite direction to finish the installation.
 
A second application is "overblowing" longer cables. Instead of laying these on figure of eight on the floor they can be blown in the FigarinO. After opening the FigarinO the cable ring can be turned around and the cable can be blown-in totally.
  • Cable Cap.: 4600 m D 4 / 2000 m D 6 / 1200 m D 7,5.
  • The FigarO replaces laying figure of 8 on the ground, is clean and space saving.
  • The FigarinO is always placed besides the cable drum.
,,,
CodeTypeBasket-D For transport kg
411150 SLK 1201260 Divisible in the middle. 71,00
6 | Cable lead in bow
Cable bow for pushing-in the cable into the FigarinO with the Minijet

,,,
,,,
CodeTypeEquipment Suitable to kg
04111521 KEB 120Cable bow Minijet-FigarinO 3,90
04111523 KEB 120MCable bow MicroJet-FigarinO 4,00
7 | Lubricant for FOC
Micro Jetting Lube, lubricant for blowing-in fibre optic cables. Excellent lubricating effect. Adheres to the duct wall and leaves the cable nearly dry, an advantage for over blowing and working in cascades with further blowing machines. Consumption approx. 10 ml per 1000 m at duct-ID 10 mm. For other duct-ID analogue

For lubrication unique and ultimate classification, Water pollution class - non-hazardous, acc. to VCI-Conception. Safety data sheets are available.
,,,
,,,
CodeTypePack. drums kg
234975 MJL 2401 bottle 0,24 l 0,32
234977 MJL 42424 bottles 0,24 l 7,50
8 | Duct cleaning sponge
Sponge for sub duct cleaning and pre-lubricating prior to cable blowing

,,,
,,,
,,,
,,,
,,,
CodeTypeD-OD D-ID Cellular Qty. kg
275398 RSM 047 4 D 8x30 20 pcs. 0,01
275400 RSM 067-10 5-6 D 8x50 20 pcs. 0,01
275402 RSM 0810-12 8 D 16x50 20 pcs. 0,02
275404 RSM 1012-16 10-12 D 20x50 20 pcs. 0,03
275406 RSM 1620 15-16 D 32x50 20 pcs. 0,06
9 | Cable guiding heads
Cable guiding heads for screwing on the cable heads for friction-low sliding during cable-blowing.

,,,
,,,
,,,
,,,
,,,
,,,
,,,
,,,
,,,
,,,
,,,
,,,
,,,
CodeTypeD/L C-D Set of kg
275517 KFM 232,3/8 2 10 0,01
275520 KFM 282,8/14 2,5 10 0,01
275523 KFM 444,4/17 4 10 0,11
275526 KFM 545,4/22 5 10 0,11
275529 KFM 646,4/23 6 10 0,03
275532 KFM 676,7/23 6,5 10 0,03
275535 KFM 747,4/23 7 10 0,03
275538 KFM 848,4/28 8 10 0,05
275541 KFM 888,8/28 8,5 10 0,06
275544 KFM 939,3/28 9 10 0,07
275547 KFM 10310,3/31 10 10 0,08
275550 KFM 11311,3/34 11 10 0,11
275553 KFM 12312,3/36 12 10 0,13
10 | Cable crash test tube
Cable crash test tube transparent with sealing end. For limiting the pushing force of the blowing-in machines. Tests without compressed air. For determination of the cable stiffness up to the crash. Safe packed in reusable plastic duct.

Essential for fail-safe adjustment of the pushing force of all different cable blowing machines. Duct-length 1 m.
,,,
,,,
,,,
,,,
,,,
,,,
,,,
CodeTypeD-OD D-ID For C-D kg
275296 CTR 05/035 3 to 2,0 0,40
275300 CTR 10/0410 4 to 3,0 0,50
275301 CTR 10/0610 6 to 4,0 0,50
275303 CTR 12/0812 8 to 6,5 0,55
275306 CTR 14/1015 10 to 8,0 0,60
275307 CTR 16/1216 12 to 9,0 0,66
275309 CTR 20/1620 16 to 12,0 0,70
11 | Duct-connector
Sub duct connector with two couplings. For closing an intermediate blowing position of a duct-OD 10 mm, on a length of max. 400 mm. Set of 3 pcs.

,,,
CodeTypeD-OD D-ID Length kg
273770 RV 101414 10 500 0,24
12 | Air connector for calibration sets
Air connector for subduct calibration sets.

Included in MicroJet PRM 196 and in Minijet P 02.
,,,
CodeTypeD-OD Press. kg
275766 DAM 1010 to 6 bar 0,08
13 | Air connectors for calibration sets
Air connectors for subduct calibration sets.

,,,
,,,
,,,
,,,
CodeTypeD-OD Press. kg
275750 DAK 1010 to 6 bar 0,39
275752 DAK 1212 to 6 bar 0,41
275754 DAK 1414 to 6 bar 0,40
275756 DAK 1616 to 6 bar 0,40
14 | Subduct-plugs of metal
Subduct-plugs of metal with plug-in coupling, for max. pressure 6 bars

,,,
,,,
,,,
,,,
CodeTypeD-OD Press. kg
275770 DEM 1010 to 6 bar 0,07
275771 DEM 1212 to 6 bar 0,13
275772 DEM 1414 to 6 bar 0,20
275773 DEM 1616 to 6 bar 0,15
15 | Conduit plug for duct-OD
Conduit plug for fixing on duct-OD with hose safety coupling applicable for duct calibration, duct pressure tests, duct cleaning etc.

,,,
CodeTypeD-OD Press. kg
2316512 KRA 2020 to 6 bar 0,40
16 | Sealing plug
Conduit sealing plug applicable for duct pressure tests.

,,,
CodeTypeD-OD Press. kg
273569 ENSA 2020 to 6 bar 0,07
17 | Air regulator for calibration sets
Air regulator with manometer for subduct calibration set.

Included in MicroJet PRM 196
,,,
CodeTypeAdjustable kg
275744 DMM 160-16 bar 1,43
18 | Air regulator for calibration sets
Air regulator with manometer for subduct calibration set.

With safety couplings for air pressure hoses.
,,,
CodeTypeAdjustable kg
275724 DMP 160-16 bar 1,90
19 | Air regulator on tripod
Air regulator valves with tripod and 5 m exit hose. An important regulator for calibration and pressure tests of cable conduits and to pressure of subducts prior blowing in conduits.

Included in duct calibration set RKV 40.
,,,
CodeTypeAdjustable Hose kg
23163007 DLR 100-10 bar Exit 5 m 11,30
20 | Case for accessory
Case for micro cabling accessory, with 9 shelves as following:
  • 4 each 132x82x105
  • 4 each 168x131x105
  • 1 of 286x168x105
,,,
CodeTypeDimension kg
275638 KZM 6040600x400x155 4,30
21 | Cable blow-in stop
Cable blow-in stop for in-house and underground fibre cable installations for cable lengths up to 200 m. Transparent duct with sponge shock absorber.

The standard rope winch is equipped with hand operated rope guide and a rope protection cover according to the rules. The winch can be equipped with the mechanical rope length measuring device SLM 510. For pulling-in fibre optic cables, subducts or delicate cables with the electronic digital line pull data recorder with USB interface, see below. For safety reason the pulling force on the bottom of drum is limited to 5,0 kN.
,,,
CodeTypeD-OD D-ID kg
275650 KES 07047 4 0,03
22 | FOC-Cable cutter
Cable side cutter for micro and mini FOC cables up to dia. 4,0 mm, length 125 mm. Knife special hardened also for Aramid and Kevlar.

,,,
CodeTypeFor FOC-D kg
255960 KSS 4,00,5-4,0 0,06
23 | Cable cutter
Cable cutter for Cu-/Al and FOC cables up to D 20 mm / 70 mm². Precision ground, hardened blades, therefore clean and smooth cut. Insulated with multi-component grips, VDE-tested. Length 200 mm.

,,,
CodeTypeFor C-D kg
255965 KSD 2020 0,36
24 | Conduit and cable slitter
Conduit slitter for lengthwise and circumferential slitting of plastic conduits and cable covers. Complete reinforced steel version. In case 195x75x45 mm.

,,,
,,,
CodeTypeTo wall thickn. L/W/H mm kg
255905 KMS 66 195x75x45 0,35
255910 ERM 6Spare knife --- 0,03
25 | Cable conduit saw
This cable conduit saw SRS 6.1 is a further development of the proven SRS 6. The saw is suitable for cutting occupied and unoccupied cable conduits without damaging internal cables or subducts. The saw is suitable for conduits at an outer diameter of 32-150 mm and at a max. wall thickness up to 6 mm. The saw can precisely cut lengthwise and crosswise and can also precisely cut windows into the cable conduit. Especially for long cuts on the cable conduits which are necessary for cable line redirections the great benefits of this saw pay off.

The cutting depth can be precisely adjusted to a 1/10 of a millimetre by an adjustment mechanism thus the cables inside the cable conduit are well-protected. The cutting depth has always to be set 0,2 mm less than the conduits wall thickness. The remaining very thin plastic membrane will be removed by a lifter tool thus the cable is also protected during this final step.
 
The conduit guiding plates allow a high safety at work as well as accurate cuts. The guiding plates are available for the below mentioned conduit-diameters. The cordless saw is handy and small in order to be fit for application also in narrow working conditions its weight is below 2 kg. Included in delivery are the following parts:
  • Accu-saw with high-quality blade hard metal equipped and 3 accus with 1 charger
  • Precise pre-adjustment of the cutting depth, 1/10 mm accurate sliding calliper.
  • Lifter for the window-cutting rest
  • Packed and delivered in robust box, 445x355x255, weight app. 6,5 kg
  • Only approx. 1,9 kg of weight for comfortable application
,,,
,,,
,,,
,,,
,,,
,,,
,,,
CodeTypeDevice For D-OD kg
273212 SRS 6.1Saw as above 32-150 6,50
273228 RFP 32Guide plate 32 0,35
273230 RFP 40Guide plate 40 0,32
273232 RFP 50Guide plate 50 0,26
273234 RFP 63Guide plate 63 0,26
273237 RFP 64+Guide plate 64-150 0,20
273222 ESB 6Spare blade --- 0,03
26 | Sub duct slitter
Sub duct slitter for lengthwise slitting. Supplied with a protecting cap.

,,,
CodeTypeSubduct occup. Subduct empty Wall L/W/H mm kg
255942 MLS 20from D 10x1,00 from 8x2,00 to 2,00 125x50x30 0,07
27 | Sub duct slitter
Sub duct slitter for lengthwise slitting and circumferential slitting of plastic conduits and cable covers. Cutter for empty and occupied subducts and dismantler for multiducts. Special thin and grinded turning guide shoe blade. Special shape of handle reduces danger of injury. Incl. 2 spare turning blades, e.g. 4 single blades.

,,,
,,,
CodeTypeSubduct occup. Subduct empty Wall L/W/H mm kg
255950 MLS 22from D 7x1,50 from 5x0,75 to 2,00 150x100x27 0,70
255955 MLE 22Spare knife for LMS 22 0,02
28 | Duct cutter
Duct cutter for occupied or empty subducts.

,,,
CodeTypeD-OD For ducts kg
272400 SDC 03143-14 occupied + empty 0,02
29 | Duct cutting tongs
Duct cutting tongs, only for use with empty subducts.

,,,
,,,
,,,
,,,
CodeTypeD-OD For ducts kg
272410 RSK 02142-14 only for empty ducts 0,10
0931240272 EM 14-- 5 spare blades for RSK 0214 0,03
272414 RSK 05255-25 only for empty ducts 0,28
0931240302 EM 25-- 5 spare blades for RSK 0525 0,02
30 | Burring tool
Burring tool for in- and outside of plastic conduits. Of lightweight aluminium

,,,
CodeTypeD-OD Dimension kg
273175 MRE 263-26 D 36x90 0,39