1 | Subduct calibration sets
The calibration sets MKV 0810 and MKV 1116 in conjunction with the micro- transmitter SKS 6 (code-no. 231941) are destined for the calibration of subducts with an internal diameter 8,0 to 16,0 mm. The calibration can be done for single subducts as well as for multi subducts. By the calibration defects or blockages on the subducts can be detected in advance thus a good blowing-in performance can be achieved.
 
The MKV 0810 set contains two calibres with different diameters for the calibration of subducts with internal diameter 8,0 or 9,8-10,0 mm. The MKV 1116 set contains three different calibres for testing subducts of ID 11,4-16,0 mm. The calibres are easily screwed onto the micro-transmitter and blown through the subducts by air-pressure. The set also contains all essential connectors, reducing nipples as well as a catcher for the micro-transmitter. The catcher has to be used in order to avoid damages to the micro-transmitter. The air-pressure for the calibration has to be limited to max. 4 bars for MKV 0810 and to max. 2 bars for MKV 1116. By applying a higher pressure the micro-transmitter might be damaged by hitting duct blockages or by hard crashing into the catcher at the very end. The set contains the following parts:
  • MKV 0810 with: each 3 calibre D 6,8 for ID 8,0 / 3 calibre D 8,5 for ID 9,8-10
  • MKV 1116 with: each 3 calibre D 9,5 / ID 11,4-12 / 3 calibre D 11,0 / ID 15-16 / 3 calibre D 12,5 / ID 15-16.
  • 6 washers to each calibre
  • 5 sponges for each calibre. 1 general catcher and different connectors and duct-reducers
  • Depending on the duct diameters different air connectors are necessary, see the following tables.
  • SKS 06, Detection frequency 33 kHz, detection depth in the ground max. 2,0 m
,Kalibrierset,calibration-set,Jeux de calibrage,231950,MKV0810
,,,,231952,MKV1116
,,,,231941,SKS06
,,,,231943,BAT06
CodeTypeDevice Subduct-ID Case kg
231950 MKV 0810Calibration set 8-10 180x140x80 1,43
231952 MKV 1116Calibration set 11,4-16 442x357x151 5,00
231941 SKS 06Micro transmitter D 6,5x84 --- 0,04
231943 BAT 06Set of batteries 10 each --- 0,04
2 | Cable conduit saw
This cable conduit saw SRS 6.1 is a further development of the proven SRS 6. The saw is suitable for cutting occupied and unoccupied cable conduits without damaging internal cables or subducts. The saw is suitable for conduits at an outer diameter of 32-150 mm and at a max. wall thickness up to 6 mm. The saw can precisely cut lengthwise and crosswise and can also precisely cut windows into the cable conduit. Especially for long cuts on the cable conduits which are necessary for cable line redirections the great benefits of this saw pay off. The cutting depth can be precisely adjusted to a tense of a millimetre by an adjustment mechanism thus the cables inside the cable conduit are well-protected. The cutting depth has always to be set 0,2 mm less than the conduits wall thickness. The remaining very thin plastic membrane will be removed by a lifter tool thus the cable is also protected during this final step.
 
The conduit guiding plates allow a high safety at work as well as accurate cuts. The guiding plates are available for the below mentioned conduit-diameters. The cordless saw is handy and small in order to be fit for application also in narrow working conditions its weight is below 2 kg. Included in delivery are the following parts:
  • Accu-saw with high-quality blade hard metal equipped and 3 accus with 1 charger
  • Precise pre-adjustment of the cutting depth, 1/10 mm accurate sliding calliper.
  • Lifter for the window-cutting rest
  • Packed and delivered in robust box, 445x355x255, weight app. 6,5 kg
  • Only approx. 1,9 kg of weight for comfortable application
,Rohrsäge,Kabelschutzrohrsäge,Schutzrohrsäge,Säge,Kreissäge,cutting-tongs,cutter,conduit saw,circular,Cisaille coupe conduites,scie circulare,273212,SRS6.1
,,,,273228,RFP32
,,,,273230,RFP40
,,,,273232,RFP50
,,,,273234,RFP63
,,,,273237,RFP64+
,,,,273222,ESB6
CodeTypeDevice For D-OD kg
273212 SRS 6.1Saw as above 32-150 6,50
273228 RFP 32Guide plate 32 0,35
273230 RFP 40Guide plate 40 0,32
273232 RFP 50Guide plate 50 0,26
273234 RFP 63Guide plate 63 0,26
273237 RFP 64+Guide plate 64-150 0,20
273222 ESB 6Spare blade --- 0,03
3 | Detection of multi ducts with average duct in the centre
Multi ducts can be detected in short distances through the average duct of dia. 12x2,0 or 14x2,0 mm laying in the centre. The micro transmitter SKS 06 of diam. 6,4 mm is screwed on the M5 thread of the mini-rod diam. 3 mm. The obtainable pushing length depends on the local condition but is limited anyway by the max. length of the mini rod of 50 m. Using lubricant relieves pushing and pulling back the transmitter. Detection depth in the ground is max. 2 m. The yellow or red mini rod can be used for inserting the micro transmitter.

,Minisender,Mikrosender,Microsender,Sender,Rohrsender,Detectors,transmitters,Conduit-calibre,duct-calibre,Detector for non-metallic conduits,mandrins,calibre de conduites,calibrage,231941,SKS06
,,,,231943,BAT06
,,,,211006,RS3-50
,,,,235130,J35V
CodeTypeDevice Subduct-ID kg
231941 SKS 06Micro transmitter from 8 0,04
231943 BAT 06Battery set --- 0,04
211006 RS 3-50Mini rod --- 1,50
235130 J 35VLubricant --- 1,00
4 | Air distributer for sub ducts
Air distributer device for 8 sub ducts

,,,,275629,DVA10
,,,,275631,DVA12
CodeTypeSubducts D-OD kg
275629 DVA 108 10 2,44
275631 DVA 128 12 2,80
5 | Spiral air hose for sub ducts
Spiral air hose with coupling for air filling of sub ducts

,,,,275633,SPS12
CodeTypeD-OD kg
275633 SPS 127-14 0,75
6 | Air distributer for subducts
Air distributer for subducts, existing of alu-distributer, manometer, plug-in coupling and ball valve with release valve.

If you want connect sub ducts Ø 12 mm with VKM 10S, you need in addition the reduction coupling RSM 12/10. This can also be used for VKM 12S for connecting sub ducts Ø 10 mm.
,,,,275620,VKM10S
,,,,275625,VKM12S
,,,,272522,RSM12/10
CodeTypeD-OD kg
275620 VKM 10S10 0,46
275625 VKM 12S12 0,48
272522 RSM 12/10Reduction 12/10 or 10/12 0,03
7 | Air connector for sub-ducts
Air connector for blowing up single sub ducts .

,,,,275610,DAS42K
CodeTypeD-OD kg
275610 DAS 42K7-14 0,44
8 | Plug and pulling head
Plug, blowing and pulling head of aluminium for subducts

,Ziehkopf,Zieheinheit,Zieheinheiten,Einziehgeschirr,Einziehgeschirre,Ziehköpfe,pulling heads, Units,Tête de tirage,mini tubes,2739904,SDV0707
,,,,2739908,SDV0715
,,,,2739912,SDV1010
,,,,2739914,SDV1211
,,,,2739922,SDV1413
,,,,2739928,SDV1620
CodeTypeFor D-D Set of Size kg
2739904 SDV 07077x0,75 10 D 7,2x44 0,51
2739908 SDV 07157x1,50 10 D 7,2x40 0,51
2739912 SDV 101010x1,00 10 D 10,2x50 0,22
2739914 SDV 121112x1,10 5 D 12,2x50 0,12
2739922 SDV 141314x1,30 5 D 14,2x50 0,11
2739928 SDV 162016x20 5 D 16,2x56 0,21
9 | Air regulator valves for sub-ducts
Air regulator valves with tripod and 5 m exit hose. Entry hose as accessory. An important regulator for calibration and pressure tests of cable conduits and to pressure of subducts prior blowing in conduits.

,,,,23163016,DLR16
,,,,23163007,DLR10
,,,,231655,KFS5/1
CodeTypePress. Hose kg
23163016 DLR 160-16 bar Exit 5 m 11,30
23163007 DLR 100-10 bar Exit 5 m 11,30
231655 KFS 5/10-16 bar Entry 5 m accessory 2,20
10 | Air pressure testing unit
Air pressure testing unit for subducts. Complete set with 7 manometers and valves. Without hoses, in alu case.

,Druckluftprüfgeräte,Druckprüfgeräte,Air pressure testing unit,Pipe-leakage-test-set,275640,RDP7
CodeTypeSubducts Press. Alu-Case kg
275640 RDP 77 0-10 bar 780/310/280 26,00
11 | Duct coupling and plug for testing subducts
Duct coupling and plug for testing subducts

,,,,275635,AKM10
,,,,275636,AKM12
,,,,275645,VST10
,,,,275646,VST12
CodeTypeArticle D-ID Press. kg
275635 AKM 10Coupling 10x1,0 6 bar 0,05
275636 AKM 12Coupling 12x1,0 + 1,1 6 bar 0,10
275645 VST 10Plug 10x1,0 6 bar 0,07
275646 VST 12Plug 12x1,0 + 1,1 6 bar 0,13
12 | Detector for micro transmitter in subducts
Detector with 8 batteries, without transmitter. For precise localisation of non-metallic conduits, and to find blockages with the conduit rods yellow or red D 3,0 mm. The following configuration is possible:
  • Yellow conduit rod with screwed on micro transmitter for spot or blockage detection
,Kabelsuchgerät, Kabelsuchgeräte,Ortungsgerät,Ortungsgeräte,Sender,Sendezange,Besenden,Detectors,transmitters,Détecteur,localisateur,231611,CAT4+
CodeTypeFrequency Transmitter L/W/H mm kg
231611 CAT4+33 kHz, without 255/70/725 2,20
13 | Air connector for calibration sets
Air connector for subduct calibration sets.

Included in MicroJet PRM 196 and in Minijet P 02.
,,,,275766,DAM10
CodeTypeD-OD Press. kg
275766 DAM 1010 to 6 bar 0,08
14 | Air connectors for calibration sets
Air connectors for subduct calibration sets.

,,,,275750,DAK10
,,,,275752,DAK12
,,,,275754,DAK14
,,,,275756,DAK16
CodeTypeD-OD Press. kg
275750 DAK 1010 to 6 bar 0,39
275752 DAK 1212 to 6 bar 0,41
275754 DAK 1414 to 6 bar 0,40
275756 DAK 1616 to 6 bar 0,50
15 | Subduct-plugs of metal
Subduct-plugs of metal with plug-in coupling, for max. pressure 6 bars

,,,,275770,DEM10
,,,,275771,DEM12
,,,,275772,DEM14
,,,,275773,DEM16
CodeTypeD-OD Press. kg
275770 DEM 1010 to 6 bar 0,07
275771 DEM 1212 to 6 bar 0,13
275772 DEM 1414 to 6 bar 0,20
275773 DEM 1616 to 6 bar 0,20
16 | Conduit plug for duct-OD
Conduit plug for fixing on duct-OD with hose safety coupling applicable for duct calibration, duct pressure tests, duct cleaning etc.

,,,,2316512,KRA20
CodeTypeD-OD Press. kg
2316512 KRA 2020 to 6 bar 0,40
17 | Sealing plug
Conduit sealing plug applicable for duct pressure tests.

,,,,273569,ENSA20
CodeTypeD-OD Press. kg
273569 ENSA 2020 to 6 bar 0,07
18 | Air regulator for calibration sets
Air regulator with manometer for subduct calibration set.

Included in MicroJet PRM 196
,,,,275744,DMM16
CodeTypeAdjustable kg
275744 DMM 160-16 bar 1,43
19 | Air regulator for calibration sets
Air regulator with manometer for subduct calibration set.

With safety couplings for air pressure hoses.
,,,,275724,DMP16
CodeTypeAdjustable kg
275724 DMP 160-16 bar 1,90
20 | Air regulator on tripod
Air regulator valves with tripod and 5 m exit hose. An important regulator for calibration and pressure tests of cable conduits and to pressure of subducts prior blowing in conduits.

Included in duct calibration set RKV 40.
,,,,23163007,DLR10
CodeTypeAdjustable Hose kg
23163007 DLR 100-10 bar Exit 5 m 11,30
21 | Conduit cutters
Conduit cutters for plain cuts.

,Kunststoffrohrschere,Kunststoffrohrscheren,Rohrschere,Rohrscheren,cutting-tongs,cutter,conduit saw,circular,Cisaille coupe conduites,273171,MRS43
,,,,273172,MRS50
,,,,273173,MRS63
,,,,273174,MRS75
CodeTypeD-OD Length kg
273171 MRS 43to 42 215 0,45
273172 MRS 50to 50 265 0,60
273173 MRS 63to 63 285 0,70
273174 MRS 75to 75 485 1,60
22 | Burring tools
Burring tools for in- and outside of plastic conduits.

Paring knife MSM 40, for separating multiple conduits.
,,,,273190,MRE63
,,,,273180,MRE50
,,,,273200,MSM40
CodeTypeD-OD Burring Mat. kg
273190 MRE 6328-63 only extern Poly. 0,20
273180 MRE 5028-50 ext. /intern Alu 0,43
273200 MSM 40Paring knife --- Steel 0,50
23 | Conduit and cable slitter
Conduit slitter for lengthwise and circumferential slitting of plastic conduits and cable covers. Complete reinforced steel version. In case 195x75x45 mm.

,,,,255905,KMS6
,,,,255910,ERM6
CodeTypeTo wall thickn. L/W/H mm kg
255905 KMS 66 195x75x45 0,35
255910 ERM 6Spare knife --- 0,03
24 | Sub duct slitter
Sub duct slitter for lengthwise slitting. Supplied with a protecting cap.

,,,,255942,MLS20
CodeTypeSubduct occup. Subduct empty Wall L/W/H mm kg
255942 MLS 20from D 10x1,00 from 8x2,00 to 2,00 125x50x30 0,07
25 | Sub duct slitter
Sub duct slitter for lengthwise slitting and circumferential slitting of plastic conduits and cable covers. Cutter for empty and occupied subducts and dismantler for multiducts. Special thin and grinded turning guide shoe blade. Special shape of handle reduces danger of injury. Incl. 2 spare turning blades, e.g. 4 single blades.

,,,,255950,MLS22
,,,,255955,MLE22
CodeTypeSubduct occup. Subduct empty Wall L/W/H mm kg
255950 MLS 22from D 7x1,50 from 5x0,75 to 2,00 150x100x27 0,70
255955 MLE 22Spare knife for LMS 22 0,02
26 | Sub duct slitter
Sub duct slitter for lengthwise slitting of plastic conduits and cable covers. Cutter for empty and occupied subducts and dismantler for multiducts. Special thin and guide shoe blade suitable for smallest subducts, see table below. Through automatic retracting of the blade damages of the cable and danger of injuries are reduced.
  • MLS 25 with special thin and guide shoe blade grinded for smallest subducts from D 4x0,5.
,,,,255952,MLS25
,,,,255956,MLE25
CodeTypeDuct occup. Duct empty Wall L/W/H mm kg
255952 MLS 25from D 4x0,50 from D 4x0,50 to 1,50 160x60x22 0,09
255956 MLE 25Spare knife for LMS 25 to 1,50 --- 0,02
27 | Duct cutter
Duct cutter for occupied or empty subducts.

,,,,272400,SDC0314
CodeTypeD-OD For ducts kg
272400 SDC 03143-14 occupied + empty 0,02
28 | Duct cutting tongs
Duct cutting tongs, only for use with empty subducts.

,,,,272410,RSK0214
,,,,0931240272,EM14
,,,,272414,RSK0525
,,,,0931240302,EM25
CodeTypeD-OD For ducts kg
272410 RSK 02142-14 only for empty ducts 0,10
0931240272 EM 14-- 5 spare blades for RSK 0214 0,03
272414 RSK 05255-25 only for empty ducts 0,28
0931240302 EM 25-- 5 spare blades for RSK 0525 0,02
29 | Burring tool
Burring tool for in- and outside of plastic conduits. Of lightweight aluminium

,Entgrater,Rohrentgrater,Burring tools,Paring knife,Tenaille pour arrondir conduit,Ebarber,273175,MRE26
CodeTypeD-OD Dimension kg
273175 MRE 263-26 D 36x90 0,39
30 | Lubricant for FOC
Jettinglube lubricant for blowing-in fibre optic cables. Excellent lubricating effect. Adheres to the duct wall and leaves the cable nearly dry, an advantage for over blowing and working in cascades with further blowing machines. Consumption approx. 0,5 l per 1000 m at duct-ID 40 mm. For other duct-ID analogue

For lubrication unique and ultimate classification, Water pollution class - non-hazardous, acc. to VCI-Conception. Safety data sheets are available.
,Gleitmittel,Kabelgleitmittel,Kabelfett,Rohrgleitmittel,Gliss,Kabelöl,Polywater,Microlube,jetting,jettinglube,Cable-duct-lubricant,grease,greasing,pump,microlube,Lubrifiant,Jettinglube,Microlube,234960,CJL1032
,,,,234965,CJL1032
,,,,234970,CJL378
CodeTypePack. drums kg
234960 CJL 10321 bottle 0,95 l 1,00
234965 CJL 103212 bottles 0,95 l 12,00
234970 CJL 3784 bottles 3,80 l 16,00
31 | Lubricant liquid
Cable lubricant Softenol, liquid, for blowing-in and for pulling-in fibre optic cables.

For lubrication unique and ultimate classification, Water pollution class - non-hazardous, acc. to VCI-Conception. Safety data sheets are available.
,,,,235800,SOF05
,,,,235810,SOF10
,,,,235830,SOF25
,,,,235890,SOF190
CodeTypePack. drums kg
235800 SOF 051 canister 5 l 5,60
235810 SOF 101 canister 10 l 11,00
235830 SOF 251 canister 25 l 26,50
235890 SOF 1901 barrel 190 l 200,00
32 | Duct cleaning sponge
Sponge for duct cleaning and pre-lubricating prior to cable blowing

,,,,275408,RSM32
,,,,275410,RSM40
,,,,275412,RSM50
,,,,275414,RSM63
CodeTypeD-OD D-ID Cellular kg
275408 RSM 3232 28 D 45x90 0,01
275410 RSM 4040 35 D 55x90 0,01
275412 RSM 5050 40 D 65x90 0,01
275414 RSM 6363 51 D 78x90 0,02