1 | Cable drum and coiling machines
Cable drum and coiling machines for cables and wires. For use in cable stores at distributors, industrial plants etc. Winding and measuring from drum to drum or to coil. Machine in stable steel construction. Drum shaft for bores from 60 mm with cones clamped by hand. Cable traversing with ball bearings to mount length measuring equipment MZ and M 20-40 / S, moving by hands. Electronic pre-set counter included as standard equipment. Included safety cage with automatic switch-off. Easy displacement through big wheels. Further accessory see below.
  • For winding from drum to drum or von drum to coils.
  • Frequency controlled drive with soft start and soft stop
  • Winding speed 15-80 rpm. Capacity: DTR 80, 400 kg, DTR 100, 800 kg
  • DTR .... F -drum lifting by hand-hydraulic.
  • DTR .... FH - drum lift by electro-hydraulic
,Handringwickelmaschinen,Kabelringwickelmaschinen,Handringwickler,Ringwickler,Ringwickelmaschinen,Kabelwickelmaschinen,Kabelwickelkopf,Kabelwickelköpfe,Rinwickelkopf,Ringwickelköpfe,Cable-spooling-machines,spooler,winder,winding-machines,Enrouleur de bobines électrique,323400,DTR80F
,Kabelschichtgeräte,Kabelschichteinrichtung,Kabelschichtungen,,,323410,DTR80FH
,,,,323430,DTR100FH
CodeTypeC-D Drum-D/W kW/Volt L/W/H m kg
323400 DTR 80F3-35 400-800/200-540 1,1/230 1,6/1,4/1,4 455,00
323410 DTR 80FH3-35 400-800/200-540 1,1/230 1,6/1,4/1,4 480,00
323430 DTR 100FH3-40 400-1000/420-710 1,5/400 1,8/1,7/2,0 530,00
2 | Cable and wire length measuring machines with electronical counter
Cable and wire length measuring machines with electronic counter for mounting on all cable winding machines and for stationary use. For this the power supply device 323.110 is necessary. Mounted on a spooling machine the power supply comes from the machine. Very robust steel construction. Due to the big perimeter of 1 m high accuracy of ± 0,5 %, accuracy class III at temperature of 5-40°C.
 
With conformity assessment according to EU Directive 2014/32/EU, Annex MI-009, valid throughout Europe. Conformity assessment procedure with type examination according to module B and product test according to module F. Equipped as standard with 3.5 inch colour touch screen incl. electronic pre-selection counter.
  • Types M ... only for insulated cables, types M ... S also for bare metal goods.
  • The accuracy refers to a calibrated cable of a length of at least 5 m.
  • Measuring machines for cable bigger than Ø 60 mm are available on request.
  • In the winding machines DTR/TR/TRG the electronic pre-set counter is installed as standard.
,,,,323720,M20
,,,,323725,M20S
,,,,323740,M40
,,,,323745,M40S
CodeTypeC-D St-rope L/W/H mm kg
323720 M 201-20 no 360/280/400 17,00
323725 M 20S1-20 1-8 360/280/400 17,00
323740 M 403-40 no 550/300/420 28,00
323745 M 40S3-40 3-22 550/300/420 28,00
3 | Roller bow
Roller bow for unwinding cables from drum of upper drum stands. For fitting at cable length measuring machines MZ or M. Steel rollers D 25 mm.
  • Type RB 4090, 90° deviation for unwinding from upper drum stands, 15 steel rollers.
,,,,322783,RB4090
,,,,3227831,RBS4090
CodeTypeSuitable for C-D Pass Bend L/W/H mm kg
322783 RB 4090MZ + M 40 max. 40 45x45 90° 400x180x380 10,10
3227831 RBS 4090MZ + M 40/40S max. 40 45x45 90° 400x180x380 10,50
4 | Conformity assessment for MZ/M 20-60/S
Application of the new EU directive 2014/32/EU (MID) has become compulsory on 1 November 2016 and it has been implemented in German law in the Verification Act (MessEG) as well as the Verification Ordinance (MessEV). Apart from the correct measurement of lengths, the requirements for the recording, confirmability and traceability of the measurements have been tightened considerably. The main change is the demand for permanent and non-corruptible storage of all measurements.

Specifically, the legislator demands that information on each measurement be stored securely, permanently and unchangeably. Apart from the actual length, the date and time of the measurement as well as information about the measuring instrument used are of relevance. All of these data are to be identified by means of an unambiguous and unique identifier, the objective being to ensure continuous traceability of each measurement. This means that machines may only be brought onto the market if they meet these requirements and have been accepted by a conformity assessment body (e.g. German Physical and Technical Institute, PTB, or the verification office) by way of a conformity assessment. The successful assessment of the measuring instruments is confirmed by the declaration of conformity issued by the manufacturer (e.g. Vetter) and is valid throughout Europe.

For companies who wish to sell the cables to third parties in the normal course of business, this means that only length measuring instruments meeting these requirements may be procured in future. The purchaser of a measuring machine with declaration of conformity is obliged to register the measuring machine with the competent verification office (in Germany www.eichamt.de) immediately following the acquisition. Machines with a declaration of conformity from Vetter are deemed duly verified until expiry of the respective nationally regulated verification period. In Germany the rule is that validity of the conformity assessment is unlimited as long as no seal is damaged or the maximum number of errors permitted in service is not exceeded (corresponds to double the value of the specified tolerance). Divergent regulations may apply in other countries. These are obtainable from the applicable national laws.

On expiry of the conformity assessment for the above-mentioned reasons, the competent verification office must carry out a reverification. Before this reverification, examination, adjustment and calibration of the measuring machine by trained personnel is recommended.

Thanks to the EU type examination certificate issued by the Federal Institute of Metrology METAS in Switzerland, machines of the new M series from Vetter can be used throughout Europe, irrespective of whether for use as measuring instruments on coiling machines or as a stand-alone solution for individual use. They offer the demanded uniformity, security, transparency and confirmability for buyers and sellers of cables within the European Economic Area. At the same time, the modular concept of the new series also enables use in direct sales or purely internal use and thus rounds off the complete range of applications for cable length measurement.

The Vetter cable measuring machines from the M../M... S series correspond to accuracy class III (+/- 0.5 %) ac-cording to EU Directive 2014/32/EU (MID) at temperatures of 5-40 °C with a minimum cable measuring length of 5 m for M machines and 10 m for MZ machines.
  • KT 001 - Declaration for MZ-MZ/S, with mechanical counter, only for direct sales or purely internal use.
  • KT 002 - Declaration for M-M/S, with electronical counter, for business use in absence of the buyer.
,,,,323700,KT001
,,,,323705,KT002
CodeTypeModule For kg
323700 KT 001F1 MZ 20-MZ 60S 0,01
323705 KT 002B+F M 20-M 60S 0,01
5 | Calibration of length measuring machines HK/HD/KDM/KLM/MZ
To confirm the testing of length measuring devices, HK/HD/KDM/KLM/MZ, according to ISO 9001 and other QM systems the calibration (KA 001) executed by Vetter is sufficient in most cases. On the other hand the calibration does not replace the EU conformity assessment whenever it comes to commercial sales of cables.

,,,,323710,KA001
CodeType kg
323710 KA 001 0,01
6 | Hand cutter
Cable or rope hand cutter including fixing plate for mounting on cable length measuring machines MZ/M 20-40.

,,,,322810,HK35
,,,,322812,HS35
CodeTypeSuitable for For C-D St-rope kg
322810 HK 35MZ/M 20-40 35 no 5,80
322812 HS 35MZ/M 20S-40S 10 10 6,30
7 | Cable cutting head, hydraulic
Cable cutting head, hydraulic for mounting on cable length measuring machines types M, for cutting insulated CU- and AL-cables, not for steel ropes.

,,,,322820,HKS40
CodeTypeSuitable for For C-D St-rope kg
322820 HKS 40MZ/M 40 40 no 11,00
8 | Coil winder collapsible
Coil winder collapsible, cylindrical, adjustable in width. For fast serving of cable rings. Capacity 100 kg.
  • After winding procedure the ring will be served through the spokes.
  • To take away the ring the coil winders flange will be folded down.
,Wickelkopf,Ringwickelkopf,Ringwickler,Wickelköpfe,Ringwickelköpfe,Coil-winder,coiler,collapsible,Enrouleur d'aneaux,322654,DTW80VK
,Wickelkopf,Ringwickelkopf,Ringwickler,Wickelköpfe,Ringwickelköpfe,Coil-winder,coiler,collapsible,Enrouleur d'aneaux,322655,DTW90VK
CodeTypeSuitable to C-winder dimens. C-D/m kg
322654 DTW 80VKDTR 80-100 D 800/420, int. 90-200 10/600, 20/140 37,00
322655 DTW 90VKDTR 100 D 800/350-420, B 90-200 10/600, 20/140 37,00
9 | Electronic cable traversing
Automatic electronic cable traversing unit to DTR 80FH and DTR 100FH. Adjustment return points and cable diameter electronic with key button and rotary switch on the control panel. Incl. cable layering arm VA 20 for sensitive cables.

,Kabelwickelmaschinen,Trommelwickelmaschinen,Kabelschneidgeräte,,,322834,REL26D
CodeTypeSuitable for For C-D kg
322834 REL 26DDTR 80FH-100FH 3-40 16,00
10 | Automatic cable diam. identification device
Automatic measuring device for identify the cable-d in all length measuring machines on cable spooling machines. The electronic cable traversing unit takes over the electronic measured values self-dependent. Manually correction of cable diameter with potentiometer in operator panel is also possible.

,,,,322930,ACD100
CodeTypeFor mounting on kg
322930 ACD 100DTR 80-100 + TR/TRG 146-206 3,00
11 | Layering-over arm telescopic
Layering-over arm telescopic for traversing sensitive cables to REL 26D on DTR machines

,,,,322786,VA20
CodeTypeSuitable for For C-D Machine kg
322786 VA 20DTR 80-100 3-40 MZ 20/40/60 8,00
12 | Control arm
Control arm with nivomat to prevent from damage of Fibre Optic and sensitive CU-cables up to D 12 mm during winding process. Light control arm of aluminium, length approx. 1050 mm, bending radius R 150 mm, with adjustable weights to the winding process. Arm is easy removable for winding of heavier cables.

,,,,322720,SAA20
,,,,322723,SAA40
CodeTypeSuitable for For C-D Length kg
322720 SAA 20MZ 20 12 1050 8,00
322723 SAA 40MZ 40 12 1050 10,00
13 | Laser-Pointer
Laser-Pointer for easy and accurate adjustment of cable traversing on cable winding machines. Fixing on layering arm or length measuring device M 20-40

,,,,322839,LP10
CodeTypeColour To mount kg
322839 LP 10red on M 20-60 / S 5,00