1 | Cable drum and coiling machines
Cable drum and coiling machines for cables and wires, series TRG. Automatic working machine for bigger cable drums. Automatic cable traversing with infinitely variable electronic setting of the cable diameter. Cable traversing ready to mount length measuring equipment M 40 - M 80. Electronic pre-set counter included as standard equipment and many other special functions. Control through central touch panel 7" with option to connection on PC. Safety cage with automatic switch-off. Further accessory see below.
  • Frequency controlled drive with soft start and soft stop.
  • Hydraulic open and closing of the lifting arms with automatic drum fixing.
  • Including coil winder collapsible, OD 800, int. D 450, width 250,
  • Coil winder speed on all machines TRG 160-250FH is 15-100 rpm.
  • Automatic swivelling of the coil winder into working position.
,Kabelwickelmaschinen,Trommelwickelmaschinen,Kabelschneidgeräte,Cable-spooling-machines,spooler,winder,winding-machines,Enrouleur de bobines électrique,323630,TRG160FH
,Handringwickelmaschinen,Kabelringwickelmaschinen,Handringwickler,Ringwickler,Ringwickelmaschinen,Kabelwickelmaschinen,Kabelwickelkopf,Kabelwickelköpfe,Rinwickelkopf,Ringwickelköpfe,,,323650,TRG200FH
,Kabelschichtgeräte,Kabelschichteinrichtung,Kabelschichtungen,,,323670,TRG250FH
CodeTypeC-D Drum-D kW/V rpm L/W/H m kg
323630 TRG 160FH10-45 600-1600 3,0/400 15-80 2,6/2,7/2,2 1.050,00
323650 TRG 200FH10-60 600-2000 5,5/400 10-70 3,0/2,4/2,4 1.250,00
323670 TRG 250FH10-80 600-2500 7,5/400 7-60 3,6/2,7/2,7 1.650,00
2 | Cable and wire length measuring machines with electronical counter
Cable and wire length measuring machines with electronic counter for mounting on all cable winding machines and for stationary use. For this the power supply device 323.110 is necessary. Mounted on a spooling machine the power supply comes from the machine. Very robust steel construction. Due to the big perimeter of 1 m high accuracy of ± 0,5 %, accuracy class III at temperature of 5-40°C.
 
With conformity assessment according to EU Directive 2014/32/EU, Annex MI-009, valid throughout Europe. Conformity assessment procedure with type examination according to module B and product test according to module F. Equipped as standard with 3.5 inch colour touch screen incl. electronic pre-selection counter.
  • Types M ... only for insulated cables, types M ... S also for bare metal goods.
  • The accuracy refers to a calibrated cable of a length of at least 5 m.
  • Measuring machines for cable bigger than Ø 60 mm are available on request.
  • In the winding machines DTR/TR/TRG the electronic pre-set counter is installed as standard.
,Kabelspulmaschinen,,,323740,M40
,,,,323745,M40S
,,,,323760,M60
,,,,323765,M60S
CodeTypeC-D St-rope L/W/H mm kg
323740 M 403-40 no 550/300/420 28,00
323745 M 40S3-40 3-22 550/300/420 28,00
323760 M 6010-60 no 700/360/600 54,00
323765 M 60S10-60 6-32 700/360/600 54,00
3 | Roller bow
Roller bow for unwinding cables from drum of upper drum stands. For fitting at cable length measuring machines MZ or M. Steel rollers D 25 mm.
  • Type RB 6090 - 90° deviation for unwinding from upper drum stands, 15 steel rollers D 25.
,,,,322783,RB4090
,,,,3227831,RBS4090
,,,,322781,RB6090
CodeTypeSuitable for C-D Pass Bend L/W/H mm kg
322783 RB 4090MZ + M 40 max. 40 45x45 90° 400x180x380 10,10
3227831 RBS 4090MZ + M 40/40S max. 40 45x45 90° 400x180x380 10,50
322781 RB 6090MZ + M 60 max. 60 65x65 90° 450x200x500 13,00
4 | Conformity assessment for MZ/M 20-60/S
Application of the new EU directive 2014/32/EU (MID) has become compulsory on 1 November 2016 and it has been implemented in German law in the Verification Act (MessEG) as well as the Verification Ordinance (MessEV). Apart from the correct measurement of lengths, the requirements for the recording, confirmability and traceability of the measurements have been tightened considerably. The main change is the demand for permanent and non-corruptible storage of all measurements.

Specifically, the legislator demands that information on each measurement be stored securely, permanently and unchangeably. Apart from the actual length, the date and time of the measurement as well as information about the measuring instrument used are of relevance. All of these data are to be identified by means of an unambiguous and unique identifier, the objective being to ensure continuous traceability of each measurement. This means that machines may only be brought onto the market if they meet these requirements and have been accepted by a conformity assessment body (e.g. German Physical and Technical Institute, PTB, or the verification office) by way of a conformity assessment. The successful assessment of the measuring instruments is confirmed by the declaration of conformity issued by the manufacturer (e.g. Vetter) and is valid throughout Europe.

For companies who wish to sell the cables to third parties in the normal course of business, this means that only length measuring instruments meeting these requirements may be procured in future. The purchaser of a measuring machine with declaration of conformity is obliged to register the measuring machine with the competent verification office (in Germany www.eichamt.de) immediately following the acquisition. Machines with a declaration of conformity from Vetter are deemed duly verified until expiry of the respective nationally regulated verification period. In Germany the rule is that validity of the conformity assessment is unlimited as long as no seal is damaged or the maximum number of errors permitted in service is not exceeded (corresponds to double the value of the specified tolerance). Divergent regulations may apply in other countries. These are obtainable from the applicable national laws.

On expiry of the conformity assessment for the above-mentioned reasons, the competent verification office must carry out a reverification. Before this reverification, examination, adjustment and calibration of the measuring machine by trained personnel is recommended.

Thanks to the EU type examination certificate issued by the Federal Institute of Metrology METAS in Switzerland, machines of the new M series from Vetter can be used throughout Europe, irrespective of whether for use as measuring instruments on coiling machines or as a stand-alone solution for individual use. They offer the demanded uniformity, security, transparency and confirmability for buyers and sellers of cables within the European Economic Area. At the same time, the modular concept of the new series also enables use in direct sales or purely internal use and thus rounds off the complete range of applications for cable length measurement.

The Vetter cable measuring machines from the M../M... S series correspond to accuracy class III (+/- 0.5 %) ac-cording to EU Directive 2014/32/EU (MID) at temperatures of 5-40 °C with a minimum cable measuring length of 5 m for M machines and 10 m for MZ machines.
  • KT 001 - Declaration for MZ-MZ/S, with mechanical counter, only for direct sales or purely internal use.
  • KT 002 - Declaration for M-M/S, with electronical counter, for business use in absence of the buyer.
,,,,323700,KT001
,,,,323705,KT002
CodeTypeModule For kg
323700 KT 001F1 MZ 20-MZ 60S 0,01
323705 KT 002B+F M 20-M 60S 0,01
5 | Calibration of length measuring machines HK/HD/KDM/KLM/MZ
To confirm the testing of length measuring devices, HK/HD/KDM/KLM/MZ, according to ISO 9001 and other QM systems the calibration (KA 001) executed by Vetter is sufficient in most cases. On the other hand the calibration does not replace the EU conformity assessment whenever it comes to commercial sales of cables.

,,,,323710,KA001
CodeType kg
323710 KA 001 0,01
6 | Automatic cable diam. identification device
Automatic measuring device for identify the cable-d in all length measuring machines on cable spooling machines. The electronic cable traversing unit takes over the electronic measured values self-dependent. Manually correction of cable diameter with potentiometer in operator panel is also possible.

,,,,322930,ACD100
CodeTypeFor mounting on kg
322930 ACD 100DTR 80-100 + TR/TRG 146-206 3,00
7 | Layering arms
Layering arms on cable length measuring machines M 40-M 80, for better cable traversing on winding machines TR/TRG 125-256, especially for soft or thin cables.

,,,,322785,VA45
CodeTypeSuitable for On machine kg
322785 VA 45M 40-60 TR/TRG 160-250 8,00
8 | Laser-Pointer
Laser-Pointer for easy and accurate adjustment of cable traversing on cable winding machines. Fixing on layering arm or length measuring device M 20-60

,,,,322839,LP10
CodeTypeColour To mount kg
322839 LP 10red on M 20-60 / S 5,00
9 | Cable cutting head, hydraulic
Cable cutting head, hydraulic for mounting on cable length measuring machines types M, for cutting insulated CU- and AL-cables, not for steel ropes.

,,,,322820,HKS40
,,,,322821,HKS60
CodeTypeSuitable for For C-D St-rope kg
322820 HKS 40M 40 40 no 11,00
322821 HKS 60M 60 60 no 14,50
10 | Coil winder with drive
Coil winder with drive for optional mounting on lifting arms of TRG 160 - TRG 250
  • Coil winder with separate drive
  • Hinged mounted on the machine.
  • Very high winding speed of 100 rpm. Capacity 150 kg.
,,,,322666,RWG80VK
CodeTypeSuitable for Dimension Cable D/m kg
322666 RWG 80VKTRG 160/200/250 D 800/350, int. 100-250 10/750, 30/80 80,00
11 | Centring sleeves for drums
Standard all drum winding units are equipped with the following centring sleeves:
  • TR 146-167 standard for centre holes of D 80
  • TR 200-206 standard for centre holes of D 80 and D 125.
  • For other centre holes special sleeves see below have to be ordered.
,,,,322864,AKZ66
CodeTypeSuitable for Fixing Form For hole kg
322864 AKZ 66TR 146-206 D 40 conic D 85-35 5,40
12 | Moving equipment, hydr.
Moving equipment for electro-hydraulic lift of the winding machine and for displacement by a hand draw bar.
,,,,322965,HG100HI
CodeTypeSuitable for Lifting Running kg
322965 HG 100HITR 166-167/TRG 160 Hydraulic manual 25,00