1 | MiniJet for Fibre Optic Cables
MiniJet, further development of the CableJet and MicroJet. For blowing-in mini fibre optic cables in long distances. Long and soft pneumatic belt drive especially for delicate cables. Produces high daily output. Electronic length and speed meter. Without cable and duct inserts. accessory and technical details see below.
Very careful but high power transmission to the cable through the soft belts.
Suitable excellent for very long cable distances with complicated design.
Simple control, high safety for operator and for cable.
Small dimension of 635x400x255 mm, weight of the machine only 21,6 kg
For compressed air up to max. 16 bar, airflow up to 5 m³/min.
MiniJet for Fibre Optic Cables,420100
CodeTypeCable-D Duct-OD Compressed air Push kg
420100 P 024-12 mm 8-40 mm 16 bar/5 m³/min. 300 N 41,00
2 | accessory-set for MiniJet
accessory-set for MiniJet P 02. All cable and duct inserts for a certain cable and duct diameter range, see below.

MiniJet for Fibre Optic Cables,420130
MiniJet for Fibre Optic Cables,420140
CodeTypeCable-D In duct-D kg
420130 SET 40-854,0-8,5 10 and 12 0,57
420140 SET 86-1248,6-12,4 14 and 16 0,56
3 | Duct inserts
Duct inserts for MiniJet for bigger duct of D 20-40 mm.

Duct inserts,420228
Duct inserts,420230
Duct inserts,420232
Duct inserts,420240
CodeTypeDuct-OD kg
420228 REM 2020 mm 0,20
420230 REM 2525 mm 0,20
420232 REM 3232 mm 0,20
420240 REM 4040 mm 0,20
4 | MicroJet for FOC, electro
MicroJet for blowing-in mini fibre optic cables. Electric drive with fine adjustment, especially for delicate cables and bundle fibres. Suitable for air pressure up to 15 bars. With digital length and speed meter. Without cable and duct inserts. accessory and technical details see below.
Very careful but high power transmission to the cable through the soft belts.
Suitable excellent for very long cable distances with complicated design.
Simple control, high safety for operator and for cable.
MicroJet for FOC, electro,422200
CodeTypeEl-Motor Cable-D Duct-OD Push kg
422200 EM 2524 Volt 0,8-3,5 3-7 mm adj. 0-25 N 16,30
5 | Receiver to EM 25
Receiver for connecting the MicroJet EM 25 to the net or to the compressor.

Receiver 230V/24VDC,275600
Receiver 230V/24VDC,275603
CodeTypeSupply from Tension kg
275600 NGE 24net 230 to 24 volt 1,00
275603 NGE 12compressor 12 to 24 Volt 3,90
6 | MicroJet for FOC, pneumatic
MicroJet basic device, for blowing-in mini fibre optic cables. Pneumatic drive especially for delicate cables D 0,8-7,5 mm. The basic for 3,6-7,5 mm can easily be upgraded with the PRA 196 for smaller cables of 0,8-3,5 mm to a real PRM 196. Suitable for air pressure up to 15 bars. Without cable and duct inserts. accessory and technical details see below.
Very careful but high power transmission to the cable through the soft belts.
Suitable excellent for long cable distances with complicated design.
Simple control, high safety for operator and for cable.
MicroJet for FOC, pneumatic,422215
MicroJet for FOC, pneumatic,422218
CodeTypeDevice Cable-D Duct-OD Push kg
422215 PR 196Basic-Equipment 3,6-7,5 7-16 mm const. 140 N 17,80
422218 PRA 196Upgrade 0,8-3,5 3-7 mm adj. 0-25 N 2,00
7 | MicroJet for FOC, pneumatic
MicroJet pneumatic drive, combined machine with adjustable electro-magnetic clutch for bundle fibres and for micro and mini cables from D 0,8-7,5 mm in ducts from D 3-12 mm. Air pressure up to 15 bars. With digital length and speed meter. Without cable and duct inserts. accessory and technical details see below.
Very careful but high power transmission to the cable through the soft belts.
Suitable excellent for very long cable distances with complicated design.
Simple control, high safety for operator and for cable.
MicroJet for FOC, pneumatic,422210
CodeTypeMotor Cable-D Duct-OD Push kg
422210 PRM 196Pneumatic 0,8-7,5 3-12 mm adj. 0-140 N 23,60
8 | accessory-set for MicroJets
accessory-set for MicroJet EM 25, PR 140 and PRM 196. All cable driving disc and cable and duct inserts for a certain cable and duct diameter range, according to table below.

MicroJet for FOC, pneumatic,422230
MicroJet for FOC, pneumatic,422236
MicroJet for FOC, pneumatic,422240
CodeTypeSuitable for Cable-D Duct-OD kg
422230 SET 08-35EM 25, PRM 196 0,8-3,5 5, 7 1,37
422236 SET 36-75PR 196, PRM 196 3,6-7,5 7, 10, 12 2,00
422240 SET 08-75PRM 196 0,8-7,5 5, 7, 10, 12 3,00
9 | Duct insert for MicroJets
Duct insert separate for MicroJet PR 140, PR 196 and PRM 196, for bigger ducts OD 14 mm and for cables up to D 8 mm.

MicroJet for FOC, pneumatic,42230132
MicroJet for FOC, pneumatic,42230134
CodeTypeSuitable for Cable-D Duct-OD kg
42230132 REM 148PR 140, PR 196, PRM 196 up to 7.5 14 mm 0,12
42230134 REM 168Cable sealing up to 7.5 16 mm 0,12
10 | UltimaZ for blow fibre units and micro cables D 0,8-4,0 mm
UltimaZ blow fibre units and micro cable blowing device especially for in-house cabling up to lengths of approx. 200 m. The UltimaZ makes it possible to continue the last mile from the underground floor to all flats. Drive through an accu-driven hand-drill. The minimal air pressure of 10-12 bars can be provided by a small compressed-air bottle. Without cable and duct inserts, see accessory and techn. details below.
Fast and easy starting operation in any spot
Feeding drive through accu drilling machine of 600 t/min. not included
The operator does not need large cable blowing experience
Small dimension of 440x370x105 mm, only approx. 2,4 kg of weight for comfortable application
UltimaZ for bundle fibres and mini cables D 0,8-4,0 mm,423300
CodeTypeCable-D Duct-OD Push Pressure kg
423300 ULV 200,8-4,0 3-12 mm 0-20 N 10-12 bar 3,80
11 | Pressure reducing valve
Pressure reducing valve up to 16 16 bar, for UltimaZ

Anpressrolle,Anpreßrolle,275717
CodeTypeDesignation Pressure kg
275717 DOU 16Pressure reducing valve 0-16 bar 0,49
12 | Pressure wheel for UltimaZ
Pressure wheel for UltimaZ, D 40, material and cable-D see table below.

Pressure wheel for UltimaZ,423340
Pressure wheel for UltimaZ,423342
CodeTypeCable-D Mat. kg
423340 KAPR 40P1,0-4,0 Polyurethane plain 0,08
423342 KAP 40A2,0-4,0 Aluminium 0,07
13 | Drive wheel for UltimaZ
Drive wheel for UltimaZ, D 40, material and cable-D see table below.

Drive wheel for UltimaZ,423340
Pressure wheel for UltimaZ,423344
Drive wheel for UltimaZ,423346
Drive wheel for UltimaZ,423347
Drive wheel for UltimaZ,423348
Drive wheel for UltimaZ,423349
Drive wheel for UltimaZ,423350
CodeTypeCable-D Mat. kg
423340 KAPR 40P1,0-2,5 Polyurethane plain 0,08
423344 KAP 41P1,0-1,6 Poly with groove 0,08
423346 KAR 421,6-2,0 pcs.eel hardened, groove 0,06
423347 KAR 4022,1-2,5 pcs.eel hardened, groove 0,05
423348 KAR 432,6-3,0 pcs.eel hardened, groove 0,06
423349 KAR 4043,1-3,5 pcs.eel hardened, groove 0,05
423350 KAR 443,6-4,0 pcs.eel hardened, groove 0,08
14 | Duct inserts for UltimaZ
Duct inserts for blowing unit UltimaZ, for duct-D see table below.

Duct inserts for UltimaZ,423358
Duct inserts for UltimaZ,423360
Duct inserts for UltimaZ,423362
Duct inserts for UltimaZ,423364
Duct inserts for UltimaZ,423366
Duct inserts for UltimaZ,423368
Duct inserts for UltimaZ,423370
CodeTypeDuct-OD Cable-D kg
423358 RKE 30163,0 mm 1,6 mm 0,05
423360 RKE 50105,0 mm 1,0 mm 0,05
423362 RKE 50145,0 mm 1,4 mm 0,05
423364 RKE 34263-4 mm 2,6 mm 0,05
423366 RKE 56405-6 mm 4,0 mm 0,05
423368 RKE 78407-8 mm 4,0 mm 0,05
423370 RKE 124010-12 mm 4,0 mm 0,05
15 | Cable sealing
Cable sealing, sets of 6 pcs. suitable for cable blowing machines and cable-diam. according to table shown below.

Duct inserts for UltimaZ,42230140
Duct inserts for UltimaZ,42230141
Duct inserts for UltimaZ,42230142
Duct inserts for UltimaZ,42230143
Duct inserts for UltimaZ,42230144
Duct inserts for UltimaZ,42230147
Duct inserts for UltimaZ,42230149
Duct inserts for UltimaZ,42230151
Duct inserts for UltimaZ,42230152
Duct inserts for UltimaZ,42230154
Duct inserts for UltimaZ,42230156
Duct inserts for UltimaZ,42021509
Duct inserts for UltimaZ,42021511
CodeTypeCable-D For blowing machine kg
42230140 KAD 100,8-1,1 mm EM 25 / PR 140 / PR/M 196 0,01
42230141 KAD 121,2-1,4 mm EM 25 / PR 140 / PR/M 196 0,01
42230142 KAD 181,4-1,8 mm EM 25 / PR 140 / PR/M 196 0,01
42230143 KAD 241,8-2,4 mm EM 25 / PR 140 / PR/M 196 0,01
42230144 KAD 332,4-3,3 mm EM 25 / PR 140 / PR/M 196 0,01
42230147 KAD 433,4-4,3 mm PR 140 / PR/M 196 / P 02 / NBK 483 0,01
42230149 KAD 534,4-5,3 mm PR 140 / PR/M 196 / P 02 / NBK 483 0,01
42230151 KAD 635,4-6,3 mm PR 140 / PR/M 196 / P 02 / NBK 483 0,01
42230152 KAD 706,4-7,0 mm PR 140 / PR/M 196 / P 02 / NBK 483 0,01
42230154 KAD 777,1-7,7 mm PR 140 / PR/M 196 / P 02 / NBK 483 0,01
42230156 KAD 837,8-8,4 mm P 02 / NBK 483 0,01
42021509 KAD 1078,4-10,7 mm P 02 / NBK 812 0,01
42021511 KAD 12410,8-12,4 mm P 02 / NBK 812 0,01
16 | Lip seals for UltimaZ
Lip seals for UltimaZ, set of 6 pcs. for cable-D see table below.

,423150
,423152
,423154
CodeTypeSize Cable-D For blowing machine kg
423150 LPD 230D 2/10,5 1,4-2,3 UltimaZ 0,02
423152 LPD 330D 3/10,5 2,4-3,3 UltimaZ 0,02
423154 LPD 430D 4/10,5 3,4-4,3 UltimaZ 0,02
17 | Duct sealing for UltimaZ
Duct sealing for UltimaZ, sets of 6 pcs. for duct-D see table below.

,423170
,423172
,423174
,423176
,423178
,423180
,423182
CodeTypeSize Duct-OD For blowing machine kg
423170 ROR 3D 3x2 3 mm UltimaZ 0,01
423172 ROR 4D 4x2 4 mm UltimaZ 0,02
423174 ROR 5D 5x2 5 mm UltimaZ 0,02
423176 ROR 7D 7x2 7 mm UltimaZ 0,02
423178 ROR 8D 8x2 8 mm UltimaZ 0,02
423180 ROR 10D 10x2 10 mm UltimaZ 0,02
423182 ROR 12D 12x2 12 mm UltimaZ 0,02
18 | Duct sealing for MicroJets and MiniJets
Duct sealing, sets of 6 pcs. suitable for cable blowing machines and duct-diam. according to table shown below.

,42230163
,42230164
,42230165
,42230167
,42230168
,42230170
,42230172
,42024014
,42024016
,42024020
,42024025
,42024032
,42024040
CodeTypeSize Duct-OD For blowing machine kg
42230163 RAD 03D 3x2,6 3 mm EM 25 / PR 140 / PR/M 196 0,01
42230164 RAD 04D 4x2,2 4 mm EM 25 / PR 140 / PR/M 196 0,01
42230165 RAD 05D 5x3,0 5 mm EM 25 / PR 140 / PR/M 196 0,01
42230167 RAD 07D 7x4,0 7 mm EM 25 / PR 140 / PR/M 196 / P 02 0,01
42230168 RAD 08D 8x4,0 8 mm PR 140 / PR/M 196 / P 02 0,01
42230170 RAD 10D 10x4,0 10 mm PR 140 / PR/M 196 / P 02 0,01
42230172 RAD 12D 12x4,0 12 mm PR 140 / PR/M 196 / P 02 0,01
42024014 RAD 14D 14x4,0 14 mm PR 140 / PR/M 196 / P 02 0,01
42024016 RAD 16D 16x4,0 16 mm P 02 MiniJet 0,01
42024020 RAD 20D 20x4,0 20 mm P 02 MiniJet 0,01
42024025 RAD 25D 25x4,0 25 mm P 02 MiniJet 0,01
42024032 RAD 32D 32x4,0 32 mm P 02 MiniJet 0,01
42024040 RAD 40D 40x4,0 40 mm P 02 MiniJet 0,01
19 | Lubricator automatic device
Lubricator for continuous greasing of the cables blown by MicroJet, MiniJet and UltimaZ. Performance and techn. details see below. Article with accessory klick here!
The Lubricator guarantees an uniform lubrication on the whole length duct length.
For mounting on MiniJet there are adapters, see below.
In the Lubricator is included an adapter for the MicroJets EM 25, PR 140 and PRM 196
Lubricator,423500
CodeTypeCable-D Duct-OD kg
423500 L 91-9 mm 4-16 mm 2,20
20 | Lubricant for FOC
Micro Jetting Lube, lubricant for blowing-in fibre optic cables. Excellent lubricating effect. Adheres to the duct wall and leaves the cable nearly dry, an advantage for over blowing and working in cascades with further blowing machines. Consumption approx. 10 ml per 1000 m at duct-ID 10 mm. For other duct-ID analogue

For lubrication unique and ultimate classification, Water pollution class - non-hazardous, acc. to VCI-Conception. Safety data sheets are available.
MicroLube for FOC,234975
MicroLube for FOC,234977
CodeTypePacking drums kg
234975 MJL 2401 bottle 0,24 l 0,32
234977 MJL 42424 bottles 0,24 l 7,50
21 | Duct cleaning sponge
Sponge for sub duct cleaning and pre-lubricating prior to cable blowing

Duct cleaning sponge,275398
Duct cleaning sponge,275400
Duct cleaning sponge,275402
Duct cleaning sponge,275404
Duct cleaning sponge,275406
CodeTypeDuct OD Duct-ID Cellular Qty. kg
275398 RSM 047,0 mm 4,0 mm D 8x30 mm 20 pcs. 0,01
275400 RSM 067,0-10,0 mm 5,5-6,0 mm D 8x50 mm 20 pcs. 0,01
275402 RSM 0810,0-12,0 mm 8,0 mm D 16x50 mm 20 pcs. 0,02
275404 RSM 1012,0-16,0 mm 9,8-12,0 mm D 20x50 mm 20 pcs. 0,02
275406 RSM 1620,0 mm 15,0-16,0 mm D 32x50 mm 20 pcs. 0,06
22 | Intermediate cable blowing head
Intermediate blowing head for finishing the left loops after blowing in two direction. Without duct inserts, without cable sealing. Max. pressure 16 bars.

Conduit-slitter,275700
Conduit-slitter,275703
Conduit-slitter,275710
Conduit-slitter,275712
CodeTypeCable-D Duct-OD kg
275700 NBK 4833,4-8,3 mm 10-16 mm 1,40
275703 NBK 8128,4-12,4 mm 12-20 mm 1,50
275710 DAP 08Air connector for NBK 483 0,50
275712 DAP 11Air connector for NBK 812 0,73
23 | Duct inserts for Lubricator and intermediate blowing head
Duct inserts with 2 sealing for Lubricator and intermediate blowing head for duct-D see table below.

Duct inserts for Lubricator,20160819
Duct inserts for Lubricator,20160819
Duct inserts for Lubricator,20160819
Duct inserts for Lubricator,20160819
Duct inserts for Lubricator,20160819
Duct inserts for Lubricator,20160819
Duct inserts for Lubricator,20160819
Duct inserts for Lubricator,20160819
Duct inserts for Lubricator,20160819
Duct inserts for Lubricator,20160819
CodeTypeDuct-OD For device kg
2016.08.19 2016.08.194 mm Lubricator L 9 0,00
2016.08.19 2016.08.195 mm Lubricator L 9 0,00
2016.08.19 2016.08.197 mm Lubricator L 9 0,00
2016.08.19 2016.08.198 mm Lubricator L 9 0,00
2016.08.19 2016.08.1910 mm Lubricator L 9 + Intermediate blowing head 0,00
2016.08.19 2016.08.1912 mm Lubricator L 9 + Intermediate blowing head 0,00
2016.08.19 2016.08.1914 mm Lubricator L 9 + Intermediate blowing head 0,00
2016.08.19 2016.08.1915 mm Lubricator L 9 + Intermediate blowing head 0,00
2016.08.19 2016.08.1916 mm Lubricator L 9 + Intermediate blowing head 0,00
2016.08.19 2016.08.1920 mm Intermediate blowing head 0,00
24 | Duct single sealing to intermediate blowing head and Lubricator
Duct single sealing to intermediate blowing head and Lubricator, for ducts-D see table below.

Duct inserts for Lubricator,20160819
Duct inserts for Lubricator,20160819
Duct inserts for Lubricator,20160819
Duct inserts for Lubricator,20160819
Duct inserts for Lubricator,20160819
Duct inserts for Lubricator,20160819
Duct inserts for Lubricator,20160819
Duct inserts for Lubricator,20160819
Duct inserts for Lubricator,20160819
CodeTypeDuct-OD For device kg
2016.08.19 2016.08.194 mm Lubricator L 9 0,00
2016.08.19 2016.08.195 mm Lubricator L 9 0,00
2016.08.19 2016.08.197 mm Lubricator L 9 0,00
2016.08.19 2016.08.198 mm Lubricator L 9 0,00
2016.08.19 2016.08.1910 mm Lubricator L 9 + Intermediate blowing head 0,00
2016.08.19 2016.08.1912 mm Lubricator L 9 + Intermediate blowing head 0,00
2016.08.19 2016.08.1914 mm Lubricator L 9 + Intermediate blowing head 0,00
2016.08.19 2016.08.1915 mm Lubricator L 9 + Intermediate blowing head 0,00
2016.08.19 2016.08.1916 mm Lubricator L 9 + Intermediate blowing head 0,00
25 | Cable guiding heads
Cable guiding heads for screwing on the cable heads for friction-low sliding during cable-blowing.

Cable guides,275517
Cable guides,275520
Cable guides,275523
Cable guides,275526
Cable guides,275529
Cable guides,275532
Cable guides,275535
Cable guides,275538
Cable guides,275541
Cable guides,275544
Cable guides,275547
Cable guides,275550
Cable guides,275553
CodeTypeHead-D/L Cable-D Set of kg
275517 KFM 232,3/8 mm 2,0 mm 10 pcs. 0,01
275520 KFM 282,8/14 mm 2,5 mm 10 pcs. 0,01
275523 KFM 444,4/17 mm 4,0 mm 10 pcs. 0,11
275526 KFM 545,4/22 mm 5,0 mm 10 pcs. 0,11
275529 KFM 646,4/23 mm 6,0 mm 10 pcs. 0,03
275532 KFM 676,7/23 mm 6,5 mm 10 pcs. 0,03
275535 KFM 747,4/23 mm 7,0 mm 10 pcs. 0,03
275538 KFM 848,4/28 mm 8,0 mm 10 pcs. 0,05
275541 KFM 888,8/28 mm 8,5 mm 10 pcs. 0,06
275544 KFM 939,3/28 mm 9,0 mm 10 pcs. 0,07
275547 KFM 10310,3/31 mm 10,0 mm 10 pcs. 0,08
275550 KFM 11311,3/34 mm 11,0 mm 10 pcs. 0,11
275553 KFM 12312,3/36 mm 12,0 mm 10 pcs. 0,13
26 | Cable crash test tube
Cable crash test tube transparent with sealing end. For limiting the pushing force of the blowing-in machines. Tests without compressed air. For determination of the cable stiffness up to the crash. Safe packed in reusable plastic duct.

Essential for fail-safe adjustment of the pushing force of all different cable blowing machines. Duct-length 1 m.
Kabel-Crash-Test-Rohr,275296
Cable crash test tube,275300
Kabel-Crash-Test-Rohr,275301
Cable crash test tube,275303
Cable crash test tube,275306
Kabel-Crash-Test-Rohr,275307
Cable crash test tube,275309
CodeTypeDuct-OD Duct-ID For cable-D kg
275296 CTR 05/035 mm 3 mm up to 2,0 mm 0,40
275300 CTR 10/0410 mm 4 mm up to 3,0 mm 0,50
275301 CTR 10/0610 mm 6 mm up to 4,0 mm 0,50
275303 CTR 12/0812 mm 8 mm up to 6,5 mm 0,55
275306 CTR 14/1015 mm 10 mm up to 8,0 mm 0,60
275307 CTR 16/1216 mm 12 mm up to 9,0 mm 0,66
275309 CTR 20/1620 mm 16 mm up to 12,0 mm 0,70
27 | Duct-connector
Sub duct connector with two couplings. For closing an intermediate blowing position of max. 400 mm. Set of 3 pcs.

Cable crash test tube,273770
CodeTypeDuct-OD/1 Duct-OD/2 Length kg
273770 RV 101414 mm 10 mm 500 mm 0,24
28 | Subduct calibration sets
The calibration sets MKV 0810 and MKV 1116 in conjunction with the micro- transmitter SKS 6 (code-no. 231940) are destined for the calibration of subducts with an internal diameter 8,0 to 16,0 mm. The calibration can be done for single subducts as well as for multi subducts. By the calibration defects or blockages on the subducts can be detected in advance thus a good blowing-in performance can be achieved.
 
The MKV 0810 set contains two calibres with different diameters for the calibration of subducts with internal diameter 8,0 or 9,8-10,0 mm. The MKV 1116 set contains three different calibres for testing subducts of ID 11,4-16,0 mm. The calibres are easily screwed onto the micro-transmitter and blown through the subducts by air-pressure. The set also contains all essential connectors, reducing nipples as well as a catcher for the micro-transmitter. The catcher has to be used in order to avoid damages to the micro-transmitter. The air-pressure for the calibration has to be limited to max. 4 bars for MKV 0810 and to max. 2 bars for MKV 1116. By applying a higher pressure the micro-transmitter might be damaged by hitting duct blockages or by hard crashing into the catcher at the very end. The set contains the following parts:
MKV 0810 with: each 3 calibre D 6,8 for ID 8,0 / 3 calibre D 8,5 for ID 9,8-10
MKV 1116 with: each 3 calibre D 9,5 / ID 11,4-12 / 3 calibre D 11,0 / ID 15-16 / 3 calibre D 12,5 / ID 15-16 mm.
6 washers to each calibre
5 sponges for each calibre. 1 general catcher and different connectors and duct-reducers
Depending on the duct diameters different air connectors are necessary, see the following tables.
SKS 06, Detection frequency 33 kHz, detection depth in the ground max. 2,0 m
Pilot rope winch,231950
Pilot rope winch,231952
Dynamometer,gauge,231941
,231943
CodeTypeDevice Subduct-ID Case kg
231950 MKV 0810Calibration set 8-10 mm 180x140x80 mm 1,43
231952 MKV 1116Calibration set 11,4-16 mm 442x357x151 mm 5,00
231941 SKS 06Micro transmitter D 6,5x84 mm -- 0,04
231943 BAT 06Set of batteries 10 each -- 0,04
29 | Detection of multi ducts with average duct in the centre
Multi ducts can be detected in short distances through the average duct of dia. 12x2,0 or 14x2,0 mm laying in the centre. The micro transmitter SKS 06 of diam. 6,4 mm is screwed on the M5 thread of the mini-rod diam. 3 mm. The obtainable pushing length depends on the local condition but is limited anyway by the max. length of the mini rod of 50 m. Using lubricant relieves pushing and pulling back the transmitter. Detection depth in the ground is max. 2 m. The yellow or red mini rod can be used for inserting the micro transmitter.

Conduit-calibre,duct-calibre,231941
Conduit-calibre,duct-calibre,231943
Mini-rod,rod,211006
Cable lubricant,235130
CodeTypeDevice Subduct-ID kg
231941 SKS 06Micro transmitter from 8 mm 0,04
231943 BAT 06Battery set --- 0,04
211006 RS 3-50Mini rod --- 1,50
235130 J-35VLubricant --- 1,00
30 | Detector for micro transmitter in subducts
Detector with 8 batteries, without transmitter. For precise localisation of non-metallic conduits, and to find blockages with the conduit rods yellow or red D 3,0 mm. The following configuration is possible:
Yellow conduit rod with screwed on micro transmitter for spot or blockage detection
Detector for non-metallic conduits,231611
CodeTypeFrequency Transmitter L/W/H mm kg
231611 CAT EM4+33 kHz, without 255/70/725 2,20
31 | Air connector for calibration sets
Air connector for subduct calibration sets.

Included in MicroJet PRM 196 and in Minijet P 02.
Conduit-cutters,275766
CodeTypeDuct-OD Pressure kg
275766 DAM 1010 mm up to 10 bar 0,08
32 | Air connectors for calibration sets
Air connectors for subduct calibration sets.

Conduit coupling plugs,275750
Conduit coupling plugs,275752
Conduit coupling plugs,275754
Conduit coupling plugs,275756
CodeTypeDuct-OD Pressure kg
275750 DAK 1010 mm up to 6 bar 0,39
275752 DAK 1212 mm up to 6 bar 0,41
275754 DAK 1414 mm up to 6 bar 0,40
275756 DAK 1616 mm up to 6 bar 0,50
33 | Subduct-plugs of metal
Subduct-plugs of metal with plug-in coupling, for max. pressure 6 bars

Rohranschlussverschraubung,Rohrverschlussstopfen,275770
Rohranschlussverschraubung,Rohrverschlussstopfen,275771
Rohranschlussverschraubung,Rohrverschlussstopfen,275772
Rohranschlussverschraubung,Rohrverschlussstopfen,275773
CodeTypeDuct-OD Pressure kg
275770 DEM 1010 mm up to 6 bar 0,07
275771 DEM 1212 mm up to 6 bar 0,13
275772 DEM 1414 mm up to 6 bar 0,20
275773 DEM 1616 mm up to 6 bar 0,20
34 | Conduit plug for duct-OD
Conduit plug for fixing on duct-OD with hose safety coupling applicable for duct calibration, duct pressure tests, duct cleaning etc.

Duct couplings,duct plugs,2316512
CodeTypeDuct-OD Pressure kg
2316512 KRA 2020 mm up to 6 bar 0,40
35 | Sealing plug
Conduit sealing plug applicable for duct pressure tests.

Duct couplings,duct plugs,273569
CodeTypeDuct OD Pressure kg
273569 ENSA 2020 mm up to 6 bar 0,07
36 | Air regulator for calibration sets
Air regulator with manometer for subduct calibration set.

Included in MicroJet PRM 196
Conduit coupling plugs,275744
CodeTypeAdjustable kg
275744 DMM 160-16 bar 1,43
37 | Air regulator for calibration sets
Air regulator with manometer for subduct calibration set.

With safety couplings for air pressure hoses.
Conduit coupling plugs,275724
CodeTypeAdjustable kg
275724 DMP 160-16 bar 1,90
38 | Air regulator on tripod
Air regulator valves with tripod and 5 m exit hose. An important regulator for calibration and pressure tests of cable conduits and to pressure of subducts prior blowing in conduits.

Included in duct calibration set RKV 40.
Pneumatic air regulator,23163007
CodeTypeAdjustable Hose kg
23163007 DLR 100-10 bar Exit 5 m 11,30
39 | Case for accessory
Case for micro cabling accessory, with 9 shelves as following:
4 each 132x82x105 mm
4 each 168x131x105 mm
1 off 286x168x105 mm
Cable crash test tube,275638
CodeTypeDimension kg
275638 KZM 6040600x400x155 mm 4,30
40 | Cable blow-in stop
Cable blow-in stop for in-house and underground fibre cable installations for cable lengths up to 200 m. Transparent duct with sponge shock absorber.

The standard rope winch is equipped with hand operated rope guide and a rope protection cover according to the rules. The winch can be equipped with the mechanical rope length measuring device SLM 510. For pulling-in fibre optic cables, subducts or delicate cables with the electronic digital line pull data recorder with USB interface, see below. For safety reason the pulling force on the bottom of drum is limited to 5,0 kN.
Cable crash test tube,275650
CodeTypeFor duct OD Duct-OD Duct-ID kg
275650 KES 07047 mm 7 mm 4 mm 0,03
41 | FOC-Cable cutter
Cable side cutter for micro and mini FOC cables up to dia. 4,0 mm, length 125 mm. Knife special hardened also for Aramid and Kevlar.

Cable crash test tube,255960
CodeTypeFor FOC-D kg
255960 KSS 4,00,5-4,0 mm 0,06
42 | Cable cutter
Cable cutter for Cu-/Al and FOC cables up to D 20 mm / 70 mm². Precision ground, hardened blades, therefore clean and smooth cut. Insulated with multi-component grips, VDE-tested. Length 200 mm.

Rohrschneidzange,255965
CodeTypeFor cable-D kg
255965 KSD 2020 mm 0,36
43 | Conduit and cable slitter
Conduit slitter for lengthwise and circumferential slitting of plastic conduits and cable covers. Complete reinforced steel version. In case 195x75x45 mm.

Conduit-slitter,255905
Conduit-slitter,255910
CodeTypeUp to wall thickness L/W/H mm kg
255905 KMS 66 mm 195x75x45 0,35
255910 ERM 6Spare knife -- 0,03
44 | Sub duct slitter
Sub duct slitter for lengthwise slitting. Supplied with a protecting cap.

Conduit-slitter,255942
CodeTypeSubduct occupied Subduct empty Wall thickness L/W/H mm kg
255942 MLS 20from D 10x1,00 from 8x2,00 to 2,00 mm 125x50x30 0,07
45 | Sub duct slitter
Sub duct slitter for lengthwise slitting and circumferential slitting of plastic conduits and cable covers. Cutter for empty and occupied subducts and dismantler for multiducts. Special thin and grinded turning guide shoe blade. Special shape of handle reduces danger of injury. Incl. 2 spare turning blades, e.g. 4 single blades.

Conduit-slitter,255950
Conduit-slitter,255955
CodeTypeSubduct occupied Subduct empty Wall thickness L/W/H mm kg
255950 MLS 22from D 7x1,50 from 5x0,75 to 2,00 mm 150x100x27 0,70
255955 MLE 22Spare knife for LMS 22 0,02
46 | Sub duct slitter
Sub duct slitter for lengthwise slitting of plastic conduits and cable covers. Cutter for empty and occupied subducts and dismantler for multiducts. Special thin and guide shoe blade suitable for smallest subducts, see table below. Through automatic retracting of the blade damages of the cable and danger of injuries are reduced.
MLS 25 with special thin and guide shoe blade grinded for smallest subducts from D 4x0,5 mm.
MLS 26 with standard thin and guide shoe blade for smalle subducts from D 7x1,5 mm.
Rohrlängsschneider,Kabelschneider,255952
Rohrlängsschneider,Kabelschneider,255953
Rohrlängsschneider,Kabelschneider,255956
Rohrlängsschneider,Kabelschneider,255957
CodeTypeDuct occupied Duct empty Wall L/W/H mm kg
255952 MLS 25from D 4x0,50 from D 4x0,50 up to 1,50 160x60x22 0,09
255953 MLS 26from D 7x1,50 from D 7x1,50 up to 1,50 160x60x22 0,10
255956 MLE 25Spare knife for LMS 25 up to 1,50 --- 0,02
255957 MLE 26Spare knife for LMS 26 up to 1,50 --- 0,02
47 | Duct cutter
Duct cutter for occupied or empty subducts.

Duct-cutter,pipe-cutter,272400
CodeTypeDuct-OD For ducts kg
272400 SDC 03143-14 mm occupied and empty 0,02
48 | Duct cutting tongs
Duct cutting tongs, only for use with empty subducts.

Duct-cutter,pipe-cutter,272410
Duct-cutter,pipe-cutter,272414
CodeTypeDuct-OD For ducts kg
272410 RSK 02142-14 mm only for empty 0,10
272414 RSK 05255-25 mm only for empty 0,28
49 | Burring tool
Burring tool for in- and outside of plastic conduits. Of lightweight aluminium

Burring tools,273175
CodeTypeDuct-OD Dimension kg
273175 MRE 263-26 mm D 36x90 mm 0,39
50 | Cable unwinder
Cable unwinder for small drums, even with damaged flanged wheels for electric installation works. Tubular steel construction galvanized. Consisting of: basic frame with 2 rubber coated wheels, one drum shaft D 25 mm with 2 cones of polyamide for hole diameter 25-80 mm.
Collapsible for easy transportation to the site.
Easy movable with the drum through big rubber coated wheels.
For drum-D up to 800 mm and drum widths up to 530 mm, drum weight max. 200 kg
As accessory steel tube drum shaft D 50, ball bearings, 2 clamps, for cones see table below.
Cable-drum-trailer,320290
Cable-drum-trailer,320292
Cable-drum-trailer,315504
Cable-drum-trailer,3155045
CodeTypeEquipment Shaft-D Cones for kg
320290 KTA 8Winder as above 25 mm Hole D 25-80 11,60
320292 KTA 8WSteel tube shaft 50 mm See next line 2,05
315504 ZKP 50-80Polyamide cones 50 mm Hole-D 50-80 0,15
3155045 ZKP 50-108Polyamide cones 50 mm Hole-D 50-108 0,39
51 | Drum unwinding stand for FOC
Drum unwinding stand for FOC or subduct drums, galvanized. Equipped with a lightweight aluminium shaft D 75 mm with drum shaft securing and 2 clamps.
pcs.urdy steel construction, hot galvanized, easy dismountable by hand for transportation.
Two crank spindles to lift the stand for unwind cables in any position.
High stability under load even in uneven places.
For drum-D up to 1400, and drum width up to 900, drum weight max. 500 kg.
As accessory alu-drum shaft D 50, ball bearings, order clamps and cones separately, see table below.
Dimensions mounted: L/W/H 1450/1400/689 mm.
Cable winding units,344355
Cable winding units,350592
Klemmschellen,Trommelschellen,350030
Cable-drum-trailer,315504
Cable winding units,3155045
CodeTypeEquipment Shaft-D Cones for kg
344355 TRG 1140Winder as above 75 mm --- 96,00
350592 TAK 5013Alu drum shaft 50 mm --- 7,40
350030 KSV 51Shaft clamps 50 mm --- 18,00
315504 ZKP 50-80Polyamide cones 50 mm Hole-D 50-80 0,15
3155045 ZKP 50-108Polyamide-cones 50 mm Hole-D 50-108 0,39
52 | FigarinO the cable basket
FigarinO. The FOC basket is used if the cable is to long to be blown completely with only one blowing machine. When half of the cable is installed in one direction the remaining cable is pushed into the FigarinO with the blowing machine. Out of the FigarinO this part of the cable can be blown uncut in the opposite direction to finish the installation.
 
A second application is "overblowing" longer cables. Instead of laying these on figure of eight on the floor they can be blown in the FigarinO. After opening the FigarinO the cable ring can be turned around and the cable can be blown-in totally.
Cable Cap.: 4600 m D 4 mm / 2000 m D 6 mm / 1200 m D 7,5 mm.
The FigarO replaces laying figure of 8 on the ground, is clean and space saving.
The FigarinO is always placed besides the cable drum.
FigarinO-basket,411150
CodeTypeBasket-D For transport kg
411150 SLK 1201260 mm Divisible in the middle. 71,00
53 | Cable lead in bow
Cable bow for pushing-in the cable into the FigarinO with the Minijet

FigarinO-basket,04111521
CodeTypeEquipment Suitable to kg
04111521 KEB 120Cable bow Minijet-FigarinO 3,90
54 | Compressor electric motor
Compressor with electric motor for blowing-in optic bundle fibres and mini cables in in-house installation. 230 Volt, without after cooler. Portable and transportable on 2 wheels. Soundproof hood. Suitable for Ultimaz ULV 20.
Electric motor 1,1 kW, 230 Volt, compressor dimensions: 560/350/560 mm
Capacity 100 l/min. at 15 bars.
Soundproof hood 71 dB(A).
Pressure reservoir 4 litre
Compressors,960102
CodeTypeAir Pressure Duct-ID Cable-D kg
960102 VE 100100 l/min. 15 bar 2,5-5,5 mm 0,8-4,0 mm 31,00
55 | Compressed air hose
Compressed air hose DN 10, L 5 m, with swing-coupling and connecting nipple for UltiMAZ ULV 20.

Pulling heads for subducts,042334015
CodeTypeDN Pressure Length kg
042334015 DLS 10/510 15 bar 5 m 1,30
56 | Y-piece wih accessory
Y-piece for connection of 2 compressors VE 100, with same pressure and volume of 15 bar and 0,24m³/min. Incl. 2 non-return valves. Connection parts are not included, the need is as following:
For duct-Ø 10 mm - Code 275.766, DAM 10, Air-connector
For duct-Ø 12 mm - Code 275.768, DAM 12, Air-connector
For compressor connection: Air hose Code 0423.340.15, DLS 10/5
Zugköpfe für Subducts,Speedpipes,275775
Kunststoffrohrschere,Rohrschere,Schere,275766
Kunststoffrohrschere,Rohrschere,Schere,275768
CodeTypeMax. pressure Duct-OD kg
275775 YVE 1615 bar --- 1,10
275766 DAM 1010 bar 10 mm 0,08
275768 DAM 1210 bar 12 mm 0,10
57 | Compressor electric motor
Compressors with electric motors and integrated after coolers. For blowing-in fibre optic min cables, fibres and bundle fibres up to length of 500 m and more. Mounted on 2 pneumatic wheels, which enables the transport on stairs for one person alone. Suitable for MicroJet EM 25.
Electric motor 2,2 kW, 400 Volt, IP 55, compressor dimensions: 1150/580/540 mm
Low sound level of 69 dBA(A).
3-fold air filters, clean, dry, oil- and water-free air.
With integrated after cooler.
Convenient for one man stair transports.
Compressors,960111
CodeTypeAir Pressure Duct-ID Cable-D kg
960111 VE 240240 l/min. 10,5 bar 2,5-6,0 mm 0,8-4,0 mm 54,00
58 | Compressor electric motor
Compressors with electric motors and integrated after coolers. For blowing-in fibre optic min cables, fibres and bundle fibres up to length of 500 m and more. Mounted on 2 pneumatic wheels, which enables the transport on stairs for one person alone. Suitable for MicroJet EM 25.
Electric motor 7,5 kW, 400 Volt, compressor dimensions: 1080x800x790 mm
Flow rate 620 l/min. at 15,0 bar working pressure
With separate after cooler
Compressors,960114
CodeTypeAir Pressure Duct-ID Cable-D kg
960114 ME 13620 l/min. 15 bar 3-8,0 mm 0,8-6,0 mm 205,00
59 | Compressor petrol engine
Compressor with petrol engine and after cooler. For blowing-in fibre optic mini cables, fibres and bundle fibres. Suitable for all MicroJets and for MiniJet P 02. The external after cooler reduces the compressed air temperature approx. 8° C above ambient temperature. The compressor is equipped with a sound absorption cover. It is portable by two pneumatic wheels.
With Honda-petrol engine 16 kW. Dimension: 1080x800x790 mm
Flow rate 1000 l/min. at 15,0 bar working pressure.
With separate after cooler electrical feeded by the compressor.
As accessory see tiltable support for after cooler, table below.
Compressors,960118
CodeTypeAir Pressure Duct-ID Cable-D kg
960118 MK 17.21,0 m³/min. 15 bar 3-12,0 mm 0,8-9,0 mm 206,00
60 | Support for after cooler
Support for the after cooler on compressor MK 17.2. pcs.eel frame hot galvanized. With this the after cooler is fixed safe and rubbery-elastic by four elements.
 
To transport the compressor in a van the after cooler is tiltable, please mind the total height of approx. 1,10 m. The after cooler can easily be dismounted from the support.
Dimension with vertical positioned after cooler, L/W/H 1170/800/1220 mm
Dimension for transportation with tilted after cooler, total height only 1100 mm
Compressors,960145
CodeTypeMaterial kg
960145 KHN 17.2pcs.eel profiles, galvanized 8,50