1 | Cable coiling and spooling machine
DE 30 - an universal cable coiling and spooling machine for cables from 1-30 mm. Suitable for coiling and spooling on smaller drums up to dia. 800 mm, of width to 400 mm. Two speed steps between 0-140 t/min. can be adapted to the cable diameter and its sensitivity. An automatic blocking device avoids to work with the wrong speed. DE 30 therefore is a machine for two applications: spooling of small electronic or telecommunication cables with high speed and spooling of bigger cables with reduced speed. For sensitive cables there is a possibility to limit the pulling force.
 
Simple and easy understandable operation through touch-screen with additional mechanical push-button. Potentiometer mounted on a pivoting operator panel. Type DE 30 SF with electronic automatic cable traversing provides an even alignment of the cable on the drum. Adjustment of the reversal points is done by push-buttons and input of the cable diameter by a control dial. Corrections of both parameters during the winding procedure are possible through laser pointer. On type DE 30 F cable traversing is done manually by the operator. Further technical details and accessory like coil winders and cable cutters see internet or leaflet no. 322
Driving power of electric motor 230/400V, 0,75 kW, torque 130 Nm
Frequency controlled soft start and soft stop
For drums up to 400 mm 0-140 rpm, for drums > 400 mm 0-80 rpm
Electronic pre-set counter for pre-selection of the cable length with automatic cut-off
Compact construction for easy rotating in shelf corridors. Dimension 1680x900x1200 mm
Coil winders,322326
Coil winders,322327
CodeTypeC-D Length meter Cable traversing Drum-D kg
322326 DE 30F1-30 LM 20-40 manual D 800x400 212,00
322327 DE 30SF1-30 LM 20-40 automatic D 800x400 252,00
2 | Power lead
Power lead from top to coiling machines DF 26-32 F/SF, two-piece. As accessory or for retrofitting of earlier supplied machines.

Electric-cable-coiling-machines,322371
CodeTypeSuitable for Height kg
322371 SZ 3DE 30 F 2,30 m 4,00
3 | Cable and wire length measuring machines
Cable and wire length measuring machines for stationary applications in connection with all cable winding machines. Very robust steel construction. Due to the big perimeter of 1,00 m the accuracy is ± 0,2 %, figure height 7 mm. Approved by the German Federal Physical and Technical Institute (PTB). Max. measuring speed 70 m/min. Please ask for an extensive offer.
Types LM ... only for insulated cables, types LM ... S also for bare metal goods.
The measuring accuracy of all LM machines is of ± 0,2 %.
The accuracy refers to a cable length of at least 20 m.
Basic machine with mech. counter, electronic pre-counter for autom. cut-off as accessory.
In the winding machines DTR/TR/TRG the electronic pre-set counter is installed as standard.
Cable length measuring machines,322736
Cable length measuring machines,322737
Cable length measuring machines,322742
Cable length measuring machines,322743
CodeTypeC-D St-rope L/W/H mm kg
322736 LM 201-20 no 360/280/400 13,30
322737 LM 20S1-20 1-8 360/280/400 13,70
322742 LM 403-40 no 550/300/420 28,50
322743 LM 40S3-40 3-22 550/300/420 28,50
4 | Leading bushings
Leading bushings for thin cables and ropes to length machine LM 20 and LM 20 S. Set of 2 paces., easy to change.

Leading bushings,322738
Leading bushings,322739
CodeTypeSuitable for Cable/wire-D Mounted kg
322738 BU 06LM 20/20S <= 5 mm no, accessory 0,16
322739 BU 14LM 20/20S <= 12 mm yes, LM 20 S 0,16
5 | Leading rollers
Leading in- and out rollers for fitting on cable length measuring machines LM 20 and LM 20 S. 4 steel rollers

Cable length measuring machines,322741
CodeTypeSuitable for Cable/wire-D kg
322741 ER 20LM 20/20S max. 20 mm 1,20
6 | Roller bow
Roller bow for unwinding cables from drum of upper drum stands. For fitting at cable length measuring machines LM 40 and LM 40 S.
Type RB 4090 - 90° deviation for unwinding from upper drum stands, 15 steel rollers D 25 mm.
RB 4018 - 180° deviation for unwinding drums from opposite drum stands, 17 steel rollers D 25 mm.
Cable length measuring machines,322783
CodeTypeSuitable for C-D Passage Deviation L/W/H mm kg
322783 RB 4090LM 40/40S max. 40 mm 45x45 mm 90° 400x180x380 10,10
7 | Automatic cable measuring device
Automatic measuring device for cable diameters on DE 30 SF. The diameter is saved automatically in the electronic cable traversing unit. For mounting on LM 20-60.

Electronic pre-set counter,322950
CodeTypeSuitable to For mounting on kg
322950 ACD 75LM 20-60 DE 30 SF 3,00
8 | Laser-Pointer
Laser-Pointer for easy and accurate adjustment of cable traversing on cable winding machines. Fixing on layering arm or length measuring device LM 20-80

Layering arms,322839
CodeTypeColour To mount kg
322839 LP 10red on LM 20 - 80 5,00
9 | Conformity assessment for LM 20-80
On January 1st, 2015 the new German Verification Act (MessEG) and the new Verification Ordinance (MessEV) entered into force. In the new Verification Act, the initial verification is replaced by the conformity assessment. The EC conformity assessment is required with first delivery of the measuring machine if the machine's purchaser sells cables in the course of trade. The declaration of conformity is valid in all EU member states. The machines are therefore deemed duly verified until expiry of the nationally regulated verification period.

Validity of the conformity assessment for cable measuring machines in retail is unlimited in Germany as long as no seal is damaged or the maximum number of errors permitted in service is not exceeded. Divergent regulations may apply in other countries. These are obtainable from the applicable national laws.
Kabellängenmessgerät,Kabellängenmeßgerät,322790
CodeTypeConformity assessment kg
322790 see aboveComment see above 0,00
10 | Declaration of Conformity for LM 20-80
In accordance with EC Directive 2004/22/EC, Appendix MI-009, a declaration of conformity may be issued by the manufacturer of the length measuring machine. Condition for this is the previous presentation at and approval by a conformity assessment body (verification office). The declaration of conformity is valid in all EU member states. The machines are therefore deemed duly verified until expiry of the nationally regulated verification period. The purchaser of a measuring machine with declaration of conformity is obliged to register the measuring machine with the competent verification office (in Germany at www.eichamt.de) immediately following the acquisition.
 
On expiry of the conformity assessment for the above-mentioned reasons (section Conformity assessment), the competent verification office performs a reverification. Before this verification, examination, adjustment and calibration of the measuring machine by trained personnel is recommended.
The accuracies of the Vetter cable measuring machines comply with the European Measuring Instruments Directive 2004/22/EC, accuracy class III, +/- 0.5 % with a minimum measuring length of 5 m
Pre-set-counter,322792
CodeType kg
322792 KT 001 0,01
11 | Calibration of length measuring machines LM 20-80
In many cases calibration (KA 001) by Vetter suffices as proof of the successful testing of length measuring devices and machines according to ISO 9000 et seq. and other quality management systems. It does, however, not replace the EC conformity assessment for the sale of cables in the course of trade.

Pre-set-counter,322795
CodeType kg
322795 KA 001 0,02
12 | Verification of LM 20-80 before 2015
The regulations for reverification have not changed. A verification that was performed before 2015 still needs to be repeated by the competent verification office every 2 years.

Kabellängenmessgerät,Kabellängenmeßgerät,322796
CodeTypeVerification before 2015 kg
322796 see aboveComment see above 0,00
13 | Coil winder fixed centre
Conical coil winder with fixed centre without foot. For mounting the coil winder on the electric machines, the adapter DWA 20 is to be ordered.

Coil-winder-fixe,322624
Coil-winder-fixe,322626
CodeTypeC-winder to Coil winder dimension Cable-D/m Cap. kg
322624 DW 18DE 30 D 300/80-90, int. 60 5/70, 10/16 10 kg 2,80
322626 DW 20DE 30 D 380/150-170, int. 100 5/200, 15/20 20 kg 3,30
14 | Adapter for coil winders
Adapter for coil winders on electric coil winding machines

Coil-winder-fixe,322620
CodeTypeSuitable for On machines kg
322620 DWA 20DW 18 + DW 20 DE 30 3,00
15 | Coil winder collapsible
Coil winder adjustable in diameter and width. Collapsible for fast serving of cable rings, including cable loop for fixing the cable head on the coil winder. As accessory also available eccentric clamp code 322.875, KE 41 for cable-D 5-30 mm.

Coil-winder-adjustable,collapsible,322634
CodeTypeC-winder to Coil winder dimension Cable-D/m Cap. kg
322634 DW 26VKDE 30 D 600/200-420, In 35-200 10/340, 20/65 100 kg 27,00
16 | Coil winder collapsible
Coil winder inside diameter not adjustable, but adjustable in width. Not collapsible for serving of cable rings, including cable loop for fixing the cable head on the coil winder. As accessory also available eccentric clamp code 322.875, KE 41 for cable-D 5-30 mm.

Coil-winder-adjustable,322639
CodeTypeC-winder to Coil winder dimension Cable-D/m Cap. kg
322639 DW 30VKDE 30 D 800/350, In 80-200 10/600, 20/140 100 kg 29,00
17 | Eccentric clamp
Eccentric clamp for fixing the cable head to the coil winder for winding procedure.

Eccentric clamp,322875
CodeTypeSuitable for For C-D kg
322875 KE 41all coil winders DW 26-50 5-30 mm 0,30
18 | Cable loops
Cable loops for fixing the cable head to the coil winder for winding procedure.

Cable loops,322869
Cable loops,322870
CodeTypeSuitable for Length Steel rope-D kg
322869 KS 265all coil winders 265 mm 2,0 mm 0,02
322870 KS 300all coil winders 300 mm 2,0 mm 0,02
19 | Adapter for drums
Adapter for wooden or plastic drums on electric coil winding machines DE 30

Ring-winder,coiler,spooler,322672
CodeTypeSuitable for Drum-D max. Drum width Cap. kg
322672 DS 32DE 30 850 mm 330-400 mm 100 kg 5,50
20 | Cable ring unwinder
Cable ring unwinder, without support TK 10.

Ring-winder,coiler,spooler,322610
Ring-winder,coiler,spooler,322611
Support of ring winder,322614
CodeTypeSuitable for For cable rings kg
322610 DA 70DE 30 D 250-600 mm, height 270 mm 8,40
322611 DA 80DE 30 D 250-700 mm, height 270 mm 12,70
322614 TK 10DH 30 Support to DA 70, DA 80 + RB 45 8,20
21 | Roller bow with adapter
Roller bow with adapter for support for unwinding cables from drums of upper stands. Please order support TK 10, code 322.614 separately.

Roller bow with adapter,322613
CodeTypeSuitable for kg
322613 RB 45DE 30 6,80
22 | Hand cutter
Cable or rope hand cutter including fixing plate for mounting on cable length measuring machines LM 20-40.

Hand-cable-cutter,322810
Hand-cable-cutter,322812
Hand-cable-cutter,322815
Hand-cable-cutter,322816
CodeTypeSuitable for For C-D St-ropes kg
322810 HK 35LM 20 35 mm no 5,80
322812 HS 35LM 20S 10 mm 10 mm 6,30
322815 HK 40LM 40 40 mm no 5,30
322816 HS 40LM 40S 14 mm 14 mm 4,80